Hi Mac Mac, I have no doubt if you build it right you should be able to get 12 VI I assume that is the same as 12watts or there abouts. I am not all that ...
406
fiditti
Dec 7, 2009 8:53 pm
Russel, Thanks for your great post to Mac Mac. We appreciate it very much. Best Regards, Fiditti...
407
fiditti
Dec 8, 2009 1:05 pm
Guys, there is a lot more to the Aethmogen web site than first meets the eye. Originally, I went there and wasn't that impressed myself. There are a lot of...
408
Russel Prier
russelprier
Dec 8, 2009 6:54 pm
There is a lot of info here if you follow every link, some are not very helpful and some are but you have to look under every stone to see what is there. The...
409
Russel Prier
russelprier
Dec 8, 2009 7:02 pm
If any of you are looking for pure iron coil cores for motors I have some here not many left. they are the old telecom relays RA talks about in his book....
410
Russel Prier
russelprier
Dec 8, 2009 8:33 pm
I have taken a telecom type 3000 relay apart and measured the pure iron core in it. Pure iron has the advangtage that it retains no magnetic memory so aids ...
411
fiditti
Dec 8, 2009 9:06 pm
Russel, Thanks for sharing your insight on the motor and the web site. Robert must have been a very sharp fellow, because you can tell by the way he writes...
412
Russel Prier
russelprier
Dec 8, 2009 9:35 pm
Yes he particually liked to lecture to university electrial engineering students and see the look on the faces of the one or two who would get it. The rest...
413
Jack R Welch
jack.welch
Dec 8, 2009 11:22 pm
Dr.Adams always had my respect and hope to learn more--JW...
415
fiditti
Dec 9, 2009 12:21 am
I just found a good source for magnet wire on e-bay. They have new 26 AWG 11 pound spools of wire for $124.99. That's not bad. Thanks....
416
fiditti
Dec 9, 2009 1:21 am
Does anyone have plans for a good motorized coil winder to make coils for the Adams motor? Since the coils take a lot of wire, a winder would be very helpful...
417
mac mac
beroywho
Dec 9, 2009 3:51 am
Funny you should ask that, Fidi. I've been collecting bits and pieces for just that purpose. I started winding some coils by hand last week and realised I...
418
mac mac
beroywho
Dec 9, 2009 3:54 am
Resources, resources. I've been looking here in Australia for a supplier with good rates. .... Yeah right. I'm sure one is out there somewhere. I'll let you...
420
Russel Prier
russelprier
Dec 9, 2009 5:18 am
I have made a distance counter which is one foot per rev then put my coil formers in a lathe and run it slowlyand go off charts that give resistance per foot...
421
mac mac
beroywho
Dec 9, 2009 5:24 am
Not quite but there is useful information in that post, Thank you Rus....
424
fiditti
Dec 9, 2009 12:10 pm
Russel, Thanks for that information. I'm going to need to use a similar method of counting the feet off my wire because the spool I think is 12,700 feet of...
426
fiditti
Dec 9, 2009 12:32 pm
I found a great source for magnet wire in USA. Their prices are very reasonable. They also carry our neo magnets. ...
427
Russel Prier
russelprier
Dec 9, 2009 6:32 pm
I will take a photo later today. Yes with small Diameter wires it is very difficult to just lay out a 1000 feet or so and not damage the insulation then...
428
fiditti
Dec 9, 2009 7:03 pm
Russel, Thanks so much. I look forward to seeing a picture of your setup. I've been trying to picture in my mind what you have there. I want to use your...
429
Russel Prier
russelprier
Dec 9, 2009 7:29 pm
Yes the little lathe I use for winding goes at 55RPM and you have to concentrate because it does not stop instantly if anything goes wrong....
430
fiditti
Dec 9, 2009 11:11 pm
Russel, That sounds great. Thanks....
431
russelprier
Dec 10, 2009 12:29 am
Hi All I have posted the picture of Robert Adams old coil winder here and my distance counter for measuring the length of wire I use. ...
432
fiditti
Dec 10, 2009 12:47 am
Russel, Many thanks for sharing the pics. It's a fantastic setup you have. Best Regards, Fiditti...
433
mac mac
beroywho
Dec 10, 2009 1:17 am
Ditto. That's one way to do it. good stuff, thank you for sharing....
434
brucefrombooral
Dec 10, 2009 9:27 am
Don't forget Rick Friedrick's new Bedini supply site //potentialtec.com/kits.html. I've been ordering parts for a while (to Aust) with no problems and good...
435
mac mac
beroywho
Dec 10, 2009 9:45 am
Hey Bruce, I've just sent away for their book by Berdon and Bedinni. figured it might help with a better understanding of the Adams motor, considering RA is no...
439
brucefrombooral
Dec 12, 2009 2:50 pm
That's a very handy site, thanks mate. I've been ordering the DVD's for the same reason, Tom's explanation of infinite energy and the words from Russel and...
440
mac mac
beroywho
Dec 13, 2009 4:10 am
442
Russel Prier
russelprier
Dec 13, 2009 6:30 pm
The first one I ever built was from a peice of bent rod passed through a peice of 4 x 2 timber with a thread on the end to hold the coil former and a crank on...
452
Oscar Obel
oscar.obel
Dec 30, 2009 1:28 pm
Hi guys, Here is a link to a similar design of Adam's http://jnaudin.free.fr/steorn/indexen.htm I read it ALL and watched the videos. VERY SIMPLE. And it looks...
