Hi Mike, What Robert had found was that as you doubled the voltage you squared the output power. It quickly becomes obvious that higher voltages have a huge...
624
Michael Scott
mike_scott91
Jan 16, 2011 2:10 pm
Hi Russel, You are an amazing source of knowledge, about Adams motors. Yes, it is clear, from the little I have learned, that Mr Adams was a very clever and...
623
windu hernowo
hernowo02
Jan 16, 2011 2:01 pm
Russel, thank you..... Does there anyone here have Adam's generator diagram that produced high voltage current (>100V) ? ________________________________ From:...
622
Russel Prier
russelprier
Jan 14, 2011 2:07 am
Hi Windu, Robert used a lot of different switching methods Digital encoder is best. Also many switching methods, star wheel is good but causes drag and can...
621
Windu
hernowo02
Jan 14, 2011 12:21 am
To me, The mechanism of the above three motors to rotate the rotor are almost similar. But the way to pulse the coil is different. I have built replication of...
620
Michael Scott
mike_scott91
Jan 13, 2011 9:04 pm
Hi Russel, This would be tremendously helpful, if you could do any of that. As you say, stuff is very thin on the ground now about Adams motors Hope to see...
619
Russel Prier
russelprier
Jan 13, 2011 7:37 pm
Hi, Sorry, there used to be a lot of genuine Adams motor info around but it seems to have disappeared lately. I will try to put together some pictures and...
618
Wardhog Dog
wildoyou
Jan 12, 2011 9:31 am
Good day all I am new to this group. I am only starting to learn about this amazing motor now. Can any body tell me where to find information that will putt me...
617
gary.clarke71
Dec 17, 2010 5:41 pm
Hi. Just saying hi to the group, i am in London/UK and have been active in alternative energy experimentation for only 8 months or so. The Adams motor seems...
615
ramg_moderator
earth_bro
Nov 24, 2010 1:50 pm
No offense taken :)...
612
Michael Scott
mike_scott91
Nov 18, 2010 11:36 am
Hi Everyone, As promised, I tracked down the U-Tube group located in Vancouver, who were posting as the "Vancouver gageteers", and who have now decided that...
611
Michael Scott
mike_scott91
Nov 18, 2010 10:06 am
Thanks, Mike ... From: Jack R Welch <jack82721@...> Subject: Re: [adamsmotor] Help wanted: To: "adamsmotor@yahoogroups.com" <adamsmotor@yahoogroups.com> ...
610
Jack R Welch
jack.welch
Nov 18, 2010 2:13 am
Hello Russ , Mike Nice to see some legit talking going on. Best to You----Jack W From: Michael Scott <mike_scott91@...> To: adamsmotor@yahoogroups.com ...
609
Michael Scott
mike_scott91
Nov 17, 2010 9:55 pm
Hi, I think it was Harwood who did the CD motor, but the Vancouver amateur group seemed to have trouble with it. They did post some U-Tube videos of it, and...
608
Russel Prier
russelprier
Nov 17, 2010 9:27 pm
Oh was that Tim Harwood? He set himself up as a self professed expert on the Adams motor. Robert got so feed up with Him he refused to answer any emails or...
607
Michael Scott
mike_scott91
Nov 17, 2010 7:31 pm
Hi Guys, & Russel, Thanks for the info. I did'nt know at all about the "Thermomotor" aspect of it. Now I do!. The vancouver people I was referring to I saw on...
606
Russel Prier
russelprier
Nov 17, 2010 6:48 pm
Hi Guys, Robert had shared some of his later technology with a company called "Glacier Bay" I think who are based in the Vancouver area somewhere. I have...
605
Michael Scott
mike_scott91
Nov 17, 2010 12:14 pm
Hi Patrick, Many thanks for your email. It's been some years since I ran a newsgroup....about nine, in fact. I had forgotten that the storage had...
604
Patrick Kelly
engpjk
Nov 17, 2010 11:08 am
Hi Mike, Good to hear that your are about to start a replication and I wish you every success in your efforts. The Files section of this group has room...
603
Michael Scott
mike_scott91
Nov 17, 2010 9:28 am
Hi, I am finally getting around to doing some serious work on an Adams motor project, now that I have just retired. I have accumulated all the internet papers...
600
Russel Prier
russelprier
Nov 15, 2010 11:04 pm
Sorry if I offended you Steve by what I said earlier. I did not realise you were the guy who set the group up but people use web names and you often dont know...
599
ramg_moderator
earth_bro
Nov 15, 2010 10:19 pm
Hi Russel, I set the adamsmotor group up back in 2004 when I was researching Roberts motor/generators. I think it existed before then though but was deleted at...
598
Russel Prier
russelprier
Nov 15, 2010 7:01 pm
Hi Steve, Thanks for that, the original moderator or group owner seems to have abandoned the group long ago. I have several projects on the go but have not...
597
Steve Knott
earth_bro
Nov 15, 2010 3:54 pm
Please accept my apologies for neglecting this group for so long. I have today gone through and removed all spam messages and banned the culprits. I will...
517
Raphael Sabaana
rsabaana
Apr 19, 2010 10:14 am
Hi, I am new in this group and wish to learn more from experienced veteran member. Thank you RS ________________________________ EMAIL DISCLAIMER! This e-mail...
512
Patrick Kelly
engpjk
Apr 11, 2010 6:54 am
Hi, Good move. As the posting volume is so low, I expect almost anyone could do the job. Patrick ... From: iron1of1 <iron1of1@...> Subject:...
485
Russel Prier
russelprier
Mar 4, 2010 2:02 am
Hi Joe, Wouldnt we all like to do that. Spin the meter backwards and get paid at the same rate we buy electricity in at. The Power Company wont wear that...
484
Joe mijdtr
joeokforme
Mar 4, 2010 1:09 am
hi russel, i am new to this technology. i like the adams motor design but i have not replicated it as of yet. i have replicated a bedini and know it works....
482
Russel Prier
russelprier
Feb 25, 2010 10:01 pm
Hi Joe, Why would you want to power one of these with an adams motor. I built an alternator just like those, page 4 of the PDF figure4 the one with ...
478
Joe mijdtr
joeokforme
Feb 25, 2010 7:16 am
anyone seen this one? Looks pretty good. I think I have the dimensions. If a trick, a damn good job. ...
