Edit chg-lib.sh and set MTX to the full path:
MTX=/opt/csw/sbin/mtx

Jean-Louis

Andreas Kuntzagk wrote:
> Jean-Louis Martineau wrote:
>> Andreas Kuntzagk wrote:
>>> Hi,
>>>
>>> I'm trying to do a (test) recovery using our SL24 changer.
>>> I set amrecover_changer and use setdevice but still get an error
>>> message when trying to extract files.
>>> Could the reason be that I did the dumps before setting
>>> amrecover_changer ?
>> no.
>>
>> Look for message in the amidxtaped.*.debug file on the tape server.
>
> Ok, this is probably the reason:
>
> 1247236826.477475: amidxtaped: changer: << <error> Fatal error from
> changer script: <none> Could not run mtx binary at 'mtx'
>
> The mtx binary is at /opt/csw/sbin/mtx so it's probably not in the
> PATH used by the recovery. But it is in the PATH of the amandabackup
> user.
> So where should I set this?
>
>>
>> Jean-Louis
>>>
>>> Here is my amanda.conf:
>>> ==========================
>>> logdir "/etc/opt/amanda/daily/log" # log directory
>>> infofile "/etc/opt/amanda/daily/curinfo" # database filename
>>> indexdir "/etc/opt/amanda/daily/index" # index directory
>>> tapelist "/etc/opt/amanda/daily/tapelist" # list of used tapes
>>>
>>> usetimestamps 1
>>> tapecycle 18
>>> runtapes 3
>>> #send-amreport-on never
>>>
>>> amrecover_changer "changer"
>>>
>>> define tapetype HP-LTO4 {
>>> comment "LTO4 Tapes, values produced by amtapetype, Compression Off"
>>> length 772096 mbytes
>>> filemark 0 kbytes
>>> speed 100612 kps
>>> }
>>>
>>> tapetype "HP-LTO4"
>>>
>>> tpchanger "chg-zd-mtx"
>>> changerdev "/dev/scsi/changer/c8t500110A00094F7C0d0"
>>> tapedev "tape:/dev/rmt/0"
>>> changerfile "/etc/opt/amanda/daily/changer.conf"
>>>
>>> holdingdisk zfs {
>>> directory "/data/backup/daily"
>>> }
>>>
>>> define dumptype global {
>>> record yes
>>> index yes
>>> auth "bsdtcp"
>>> program "GNUTAR"
>>> }
>>> ========================
>>>
>>> and here the amrecover session:
>>>
>>> ========================
>>> amrecover> setdevice -h fileserver07 changer
>>> Using tape "changer" from server fileserver07.
>>> amrecover> extract
>>> Extract list empty - No files to extract!
>>> amrecover> add proteome
>>> Added dir /proteome/ at date 2009-06-25-13-49-29
>>> Added dir /proteome/ at date 2009-06-30-10-01-43
>>> Added dir /proteome/ at date 2009-07-02-10-48-40
>>> Added dir /proteome/ at date 2009-07-03-10-51-17
>>> amrecover> extract
>>>
>>> Extracting files using tape drive changer on host fileserver07.
>>> The following tapes are needed: test019
>>> test021
>>> test004
>>> test005
>>>
>>> Restoring files into directory /data/test
>>> Continue [?/Y/n]?
>>>
>>> Extracting files using tape drive changer on host fileserver07.
>>> Load tape test019 now
>>> Continue [?/Y/n/s/d]?
>>> Volume labeled 'test019' not found.
>>> Load tape test019 now
>>> Continue [?/Y/n/d]?
>>>
>>> ======================
>>>
>>> regards, Andreas
>>
>