Hi Brent Good explaining model you made there. Well I believe you understand it correct. Was it the standing model you worked on? The only thing I can think of...
Christian, That may be what is happening. I have uploaded StandingModel_Copy.zip. I added a moment to the L5-S1 joint (just below the body models in Main)....
Hi Brent I have been looking at your model, I can see there must be something wrong. I haven't figured out what it is yet... but I am still looking at it....
Hi Christian, I added moments at all the other lumbar joints, and it seems to be working as expected: with a lower max muscle activity with the help of the...
Hi, I try to run Gait3D using our own motion data. I copied the AnyBody Gait3D model, run it using your data, it works fine. I then replaced all your data...
Hi John I will try to guide you through some steps, these are the steps i followed trying to make the model run kinematically. 1: Make sure the model has the...
... Søren: Thanks for the fast response and detailed instruction. I have downloaded your files and it runs. I can now refine the model from here. John...
Good day Mark, I have a few more questions for you if you don’t mind. 1. In the repository, in the toolbox section, the Kit Vaughan set of markers is...
Hello Jean-Olivier, Mark went on paternity leave on March 1, so he may not be able to answer for a while. I am not sure whether he follows the group from home,...
Hello Søren, In step 2 you specify that John should check the locations of the markers. When you say that, you mean that the marker locations, as specified in...
Hi John, I'm absolutely sure he's got his hands full and I wish him great times! Congratulations to him! Actually, I hope he won't be looking at his e-mails...
hi all, started using this software, and am wondering if anyone has an example of how to enter position data into the drivers, i want to be able to move for...
Hello "atlas" First of all welcome to the group. What you need to do is to add a node at the segment you want to drive and then drive that node with your...
Hi AnyBody-Team, i am working with a shoulder-model from the repository for my diploma- thesis. I used the building block tutorial and included the files ...
Søren: Following your suggestions, I have adjusted the model posture, and got the model working user my own data. I am working further with my model, trying...
Hello Søren, I'm back with another question, what a surprise! *lol* In my model, I have a AnyKinEqInterPolDriver to drive the 5 arm angles, namely: elbow -...
Hi Alex I will try to answer your questions. The property GhReation.FTotal i measured in the global coordinate system, you can see how it is calculated in the...
Hi Venn In principle you should be able to replace an AnyKinEqSimpleDriver with an equivalent interpolation driver. Here are some quesses on what could go...
hey ppl ! this is Zahid. I'm a new member to this group. i'm currently doing my master's in mechanical engg at michigan state univ(US). i'm working on...
Hello Zahid, and welcome to the group. Yes, the AnyBody Research Project has a project called the Seated Human. There is a poorly updated homepage about it...
Hi Søren,It was a stupid mistake on my part... didn't convert the angles to radians! It was the first place I checked, but I some how missed it the first time...
S�ren, Thanks for the great job. I can now work to adjust the model. In fact, the attachment locations of the stilts to the legs have not been carefully...
Hi again, I still have been unable to correctly drive a segment using positions, I can use the AnyKinEqInterPolDriver with reference to a joint and drive a...
I found the errors in my last post, especially at measure(),my current file will compile but i'm getting an overconstrained message, my thought was as shown in...
Hello, I have a problem regarding the posture of the Standing Model. I have been investigating the effects of multiplanar deformities of the femur on knee...
Hi Ceren I will start by exaplaining how the standing model is driven, it is all going on in the JointsAndDriver.any file, then i will describe the concept of...
Hi Atlas? You have a problem consisting of one seg and a revolute joint this is a problem with one dof. This means you can drive one dof only, you try to drive...
Hello Søren, Thank you for your response. Basically, what I am trying to do is to put the body in a specific posture, and then investigate the changes in...
Hi Ceren I assume that you want the model to be standing and have reactions on the feet, then the standing model is still good choice. You can adjust the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
