Hi Sören, the error has to be in one of the used BRep-Files. I hoped you would have an idea where to look without uploading the whole used BRep-Includes. When...
Hi Sarah It sounds reasonable to use the a marker at the AC joint but i think you should not drive this marker medial laterally but only in for/back up/down...
Hi Maren I have some other ideas about which files to look into Arm3D/jnt.any is the file describing the joints of the arm, if you did anything changes in this...
Hi Sören, thank you for this hint: it was an accidently outcommented line in the Arm3D/jnt.any file. Now everything is fine again. Thank you very much, best...
... Can you explain me the value of: lower_lumbar_spine,upper_lumbar_spine,lower_thoracal_spine,upper_thoraca l_spine,lower_cervical_spine,upper_cervical_spine...
Hi Søren: I am applying Gait3D using my own data. The model seems working and the magnitude of the joint moments are also OK. But the predicted magnitude of...
Hi Frank If you look in the ARep/Aalborg/Gait3D folder you can find a file named AnyMan.any, i think this file will solve your problem. Please look in the...
Hi John I have tested your model and found a few things 1: the position of the CentrOfPressure segment seem to be too low. This can be corrected by adding a...
Hi, I've looked in that Folder (AnyMan.any) but i don't really understand where do the coefficients come from. from AnyMan : AnyVar lower_lumbar_spine =...
Hi John I have looked a bit more into the model I think the main problem could be the kinemtatics. I tried again to insert a reaction force on the right and...
Hello Franck, This is John from the AnyBody Research Project. As you may know, the models in the repository are the results of a lot of rather uncoordinated...
Hi Søren: Thanks for your time and efforts. I agree with you that the problem is likely caused by the kinematics. But, it is a tough job. I have spent a lot...
Hi Søren: I have improved the model a little bit. It can now run to the end. But, the kinematics is still a problem. The updated model is Gait3D_rev3, which...
Hi, last year in August you explained what PEFactor is used for. You gave me the example that if the PEFactor is 5 , i can theoretically pull the muscle five...
Hi Maren The easiest way to obtain the passive force versus muscle length is to equip the model with reaction forces in the all the human joints. Then all...
Hi Silke Sorry about the slow repond on this message... The reason why your muscles forces are going up after you applied your drawvector is that you are also...
Hi John I have tried to optimize the kinematics using an optimizer made by Michael Skipper Andersen, who is working on a Ph.D. project, about kinematic...
Hi Søren: I believe the best way to solve the problem is the kinematics optimization. The model should be stable, if you can solve the over-constrained...
I have a question regarding RecruitmentSolvers, specifically the MinMaxNRSimplex solver (although I'm sure my question applies to the other Recruitment Solvers...
Hi John The kinematic optimizer is working on a model which has a fixed topology, so i can not specify a specific dof like the eversion of the ankle to be...
Hi, I just got to know about anybody and wish to used it to do a modeling of single landing to calculate the joint force in the knee.But i am not familiar with...
Hello Eugene Welcome to the group. Yes you can apply motion capture and force data to the models, which I guess would be necessary in your case. To get going...
Hi All, I am a new comer to this group and AnyBody. One of the first problems i have come across is determining is the number of degrees of freedom of the...
Hi Soeren: Finally I got my model working. It's now a "clean" solution, without using AnkleEversion driver, just driving via motion markers. It seems the...
Hi... I'm working with the intra-abdominal pressure, or better described, I'm looking at the file that models the abdominal pressure, which is the Buckle.any....
Hi Shashank Welcome to the group. If you run the ModelInformation after the model is loaded, then a list of constrains and DOF will come up. The DOF have names...
Hi Shashank This is just some extra info to what Christain already wrote. All applications have a file named Mannequin.any, this file has a folder named...
Hi Sarah I have uploaded a new version of you application to the file section of the group it is named "SarahArmModel – Muscles_6-11-07V2" . I have updated...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
