Hi Eugene Yang Thanks for the model. I downloaded it and took a look. It does run but do not move because of the large kinematicTol you set on. If you change...
Christian: I have a question about the scaling. I understand that the LengthMass or LengthMassFat is more reasonable than the Uniform scaling. But, I got...
Hi Christian, Thank for your previous suggestion. Correct the gray markers are what i obtain using MOCAP and the blue are those specify in Kt Van. Markers. I...
Hi John This error is related to the muscle wrapping of the iliopsoas muscle, it has failed to solve the wrapping. Apparently the change of the scaling...
Hi Eugene Here are some answers to your questions: 1 If you have not done modifications to the original JointAndDriver.any file the knee is driven in the X...
Hi Soren, I had attached a new folder name "Landing Gait" of my single leg landing model. I did not use the same constraint as in Gait3D. I still have problem...
Hi Eugene I have tried to improve the kinematics of your model by making changes to the following files JointAndDrivers.any Here the drivers setup now more...
Hi Soren, Thanks for the help. It seem to be moving fine. Regarding the StrengthParameters, how do i know that the Strength indexLeg is correct and what value...
Hi Eugene It is difficult to say what the exact number should be for the IndexLeg, if your subject was an athlet. If you increase the strenght of the legs by a...
Dear AnyBody Team, I'd like to get L5/S1 joint moments from an AnyBody standing model. Joint reactions appear to give compressive forces, and there is ...
Could someone just refresh my memory as to how the wrist muscle file works exactly? I am currently applying a force to the palm joint of: (-82.3, 82.14, 21.2)...
Hello everyone, I am working on a foot model and I have been modeling digotorum extensor and flexor muscle as 4 different muscles. I am curious, if there is a...
Hi Sunwook I think the joint you are looking for is the L5Sacrum joint in the model. You are correct that joint reactions in the spine are the reaction forces...
Hi Sarah It is a good question. The muscle forces you get is the wrist moments not forces, so the numbers you have listed are the moments generated by...
Hi Prabhav The solution you describe is currently the only way to do this. You need to define an intermediate segment for connecting the muscles. This poses...
Hi Soren I have some question which I am not sure how to answer and need your advise. For my model, the StrenghtIndexLeg is 1.5, and SpecificMuscleTensions is...
Thank you for the quick response. I just checked JointMuscles folder to see positive and negative muscle outputs for L5SacrumJnt, using the No_Muscle model. ...
Hi Eugene I yes i think you should increase the strengh of the muscle group with the same amount unless you know that the subject have particular strong legs...
Hi Sunwook I am not sure what was the size of you hand load so i can not judge if the moment of 39Nm is ok or not. If the way you have applied the forces are...
Hello Soren, Thank you for the inputs. As you suggested, I did simple checks. First, I checked a fixed posture (i.e., 70 degree flexion) without hand loads....
Hi Sunwook It sounds as it could be a dynamic issue that kick in here maybee. To check if this is the case please try to increase the tEnd value of the...
Dear Subscribers, It is the summer holidays around here right now, so our staffing is much smaller than usual. This also means that the replys from our support...
Thanks for your help, I really appreciate it. I think I understand where to now find joint forces and moments. Just to clarify though, when I go to the model...
Thanks Soren for the quick reply.. One more question, how can I calculate moment arms for the muscle. It is mentioned in the tutorials, but I couldnt find the...
Hi Prabhav I think you wanna take a look at AnyForceMomentMeasure, which you can use for measuring moments and forces. Best regards Christian, AnyBody Support ...
Hi Sarah To me it sounds all right:) Best regards Christian, AnyBody Support ... where to now find joint forces and moments. Just to clarify though, when I go...
Hello all, Since I needed to analyze data generated by Anybody using MatLab, I wrote a script that reads AnyOutputFile and creates a structure storing all...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the anyscript group. File : /readABO.rar ...
anyscript@yahoogroups...
Jul 16, 2007 4:02 pm
1386
Dear Soren, I made changes as you suggested. And it seems to be working now. Thank you for the quick responses. However, I have one more question on the sign...
Sorry to both you again, but just when you thought you were done with me... I thought of another question! :-P When I get joint force outputs from the path I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
