Hi Shreeganesh I have made some changes in the model and uploaded it again using the name “testfiledumbV2” The problem was the following: You have added 2...
Hi Abra Please upload the model to the file section of the group. When the model fails, please try to have a look at which of the constraints violations is...
Hi Soeren, Thanks for the advice. I looked at the constraint violations, and none seems noticeably larger than the others. I have uploaded the file to the...
Hi Abra, The problem lies in the left leg, you can simply see it in the model view: the left knee is suddenly deviating sideways and the foot takes a strange ...
Hi Soren, Thank a lot . I am running tests on the model .I will get back to you for more queries.Thank you again . Sincerely, Shreeganesh Sudhindra ... From:...
Hi Soren and thanks for your quick and substantial response. Unfortunately I have not been able to investigate on changing the recruitment criteria yet, but it...
Hello !! I am Simon and I study at the University of Luxembourg. I am making a new model to simulate the flexion of Knee with a lying down fullbody without...
Hello Simon, The description of the error message: OBJ.MCH.KIN3 (Fatal error) ERROR(OBJ.MCH.KIN3) : 'ObjectName' : Kinematic analysis failed in time step ...
Hi Michael It looks fine the way you apply the force to the knee, as long you ensure that the plate has no reactions to environment and no force applied when...
Hello guys, As some of you may know, I am working on a sit-to-stand model. My model is based on the old Gait model (lower-limb) and uses orientation to drive...
Hi Jean Olivier, I run the model with version 3.0.1 and 3.0.2 (I don't have 2.x currently installed) and Rep6. The driver AnyKinEqSimpleDriver RthighRotDriver...
Hello Sylvain, Thank you very much for your help and time. It seems the values we're in fact identical, my mistake comes from a small bug that prevents from ...
Hi, It is good to know that you fixed it and that it was not a bug in the AnyForceMomentMeasure. Good luck with your work. Best regards, Sylvain, AnyBody...
Hello, I have a couple of questions regarding AnyForceMomentMeasure2. I'm trying to calculate the hip moments in the GaitVaughn model. I've looked at post 2117...
Hi Soren, I am developing a Matlab Interface for anybody .I would wish to include the Model view and the chart view 2D/3D of the anybody model in matlab gui ....
Hi, I'm trying to build a model of an 8 yr old during a gait cycle. As the gait between this age and adult gait is not too different, I'm adapting the...
Hi Abra, The mentioned code will actually give the moments created by the reaction forces of the joint because no muscles are listed. I assume you want the ...
Hello Pete, If you just scale the model it will not deliver the right results. What is your approach for the ground reaction forces? Best regards, Sebastian ...
Hi Pete !! It good your idea to scale the model, but you must scale with the same ratio the mannequin,the folder which contain all sensors. You try to look if...
Hello!! Please in the folder JointAndDrivers of the GaitVaughan model,I don't understand the line "Coef ={-1,-1,1}"of this paragraph: AnyKinEqSimpleDriver...
Hi Shreeganesh, Right now this is not a feature of the system. Even so you can create outputfiles which you may use in Matlab to create your plots. Best...
Hi Simon, Please refer to posting Nr. 2202, a description of the driver can be found there. Best regards, Sebastian _____ From: anyscript@yahoogroups.com...
Hi Sebastian Thanks for your reply (and simon). I don’t quite understand how to scale the model correctly so apologies for all the questions. Unfortunately,...
Dear Support, Hello. I would like to know about "IF .. then .. else .. " function. Many programming languages have "IF.." function. If it exists in AnyScript,...
Hi All My research is analyze ligament of knee but in repository7.1 not have example of ligament so I will build ligament into knee. How I will input ligament...
Hi Pete, In my opinion it's not the best solution to simply scale the ground reaction forces. It will be difficult to get good results out of this. You could ...
Hi Wongsakorn, Basically you have to define new AnyRefNodes on the segments you want to connect, e.g. on the Thigh and Shank. Then you have to define the...
Dear AnyBody, I am trying to do a comparison of optimisation methods available in GaitApplication2. When trying to run the model on POSVELACC in the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
