Hi Soren, At first and the most important thing is thank you very much because you have answered fastly to our mails. Your help is being very important for our...
Hello, my name is Niclas from FH Aachen. I have some questions regarding the modeling of the spine from TH 12 up to C1. 1.) In which way is the curvature of...
Hi Niclas I am not sure if i understand your first question. The spine is driven by a spine rhythm which automatically sets the rotations in the joints of...
Hi Soren, The last week you said me that I use "ScalingLengthMassFat" in Mannequin file because it is the most complety scaling option. When I run the...
Hi Raul The error you get is due to a wrapping muscle, which fails to converge. The remedy is normally to increase the number of points used for the muscle...
Hi Soren, Thanks for your quick replies. This time, I have uploaded my model "Prabhav--Leg model" in group files for you to test. Problem I am facing is that...
Hi, I would like first to thank John for his reply (Positions & Drivers). My model works fine now. I'm trying to make another model following the building...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the anyscript group. File :...
anyscript@yahoogroups...
May 3, 2006 11:32 pm
530
Hi Prabhav I have looked through your model, i have found no errors in the way you define joints, drivers etc. I think it is the muscle configuration which...
Hi Fred I have changed a bit in your model and uploaded a new one FredModelV2.Zip In the Environment.any ile I have added a handle bar segments which the hands...
Hi Soren, I changed "Spline.SringMesh" from 45 to 40 and the last error was solutioned but we have been doing tests and it continues to give other error, it...
Hi Raul You write that you have decreased the Spline.StringMesh from 40 to 45. I recommended an increase of about 10 points or maybee more, please try this, if...
Hi Soren, I change the parameter "Spline.StringMesh" but the errors not stop. I say the procedure and the changes that I did it. "4) Kinematic analysis... ...
Hi Raul I tried to debug your model, but there was only the main file, i also need the AnyRaul.any file and the other files in that dir. Please zip the entire...
Hi Soren, We're investigating the AnyBody Programming. On an Excel sheet we list all muscles and we select on the Excel sheet the ones that we want to show on...
Hi Raul I have now tested your model, the problem is the number of timesteps. You have a very large motion using only 5 timesteps, this can cause diffilculties...
Hi, I'm using FredModelV2 (cf. Post "RE : Building block tutorial") and I have changed some lines in Environment.any, Mannequin.any, JointsAndDrivers.any files...
Hi Fred I have tried to run the FredModelV2 from the files section, but i can not remake your pictures. The model assembles in the same way each time. It is...
Hi Fred We are not aware of a good free tool for this purpose. We normally recommend the product VideoMach from www.gromada.com the cost is 30$, so it is not...
Thank you very much Soren. I found a freeware which works well. I could send it to you if you want to try. I'm using it for my model and results "sound" very...
Hi Fred This sounds very interesting, please just post a reply with a link in if you have it, then the other users will be able to see this. Best regards ...
Hello Soren, Is there a measure of much much a muscle contract during its motion? In particular, the strian (change in length/original length ) of muscle...
Hi Leng-Feng There is no direct measure of the muscles strain as direct output from the system, but you can easily compute from the standard output. This small...
Hi Soren, We would like to change the muscle colors and the color names(the label). By the moment, we have got to change the muscle colors. We have created...
Hi Raul In principle this is possible and you seem to be doing it in the right way. Unfortunately it seems that some graphics cards have a problem showing the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
