Hi All, Anyone who uses this Coupon needs to be hung, drawn and quartered for supporting spammers. Actually, anyone using this website/company needs to be...
Hi, Occasionally, when I pick up the phone to an incoming line, I get a short burst of echo. The receiver hears a voice that's cutting in and out, then it...
... Is this a problem with an FXO module or an FXS module? Ie SIP -> FXS -> Cordless phone? or PSTN -> FXO -> FXS -> Cordless phone? or PSTN -> FXO -> SIP...
Hi Guys, Is anyone working on BSD drivers for this card? Its not being pickup by the basic asterisk. I'm told they work ok in linux and yeastar have a driver...
Hi Daniel, I would have thought that " Fully - Supported Zaptel Compatible Hardware" would mean that it works with the default drivers. Also, be sure that this...
Hello everyone. I was wondering if I could get some sort of help with a Trixbox Setup for home. Basically this is the setup so far. - All computers have...
The company I workd for is switching over to Asterisk and it looks like Broadband Solutions is the front-runner as VSP at the moment. Has anyone had experience...
... Try looking through this guide, http://dumbme.voipeye.com.au/trixbox2/trixbox2_without_tears.pdf Also have a look on forums.whirlpool.net.au. i know it can...
Hi Nathan, Please contact me offlist if you would like some further assitance. bizebox@... Thanks. Scott. ... [Non-text portions of this message have...
Hi, I keep getting the message "Got SIP response 400 "Bad Request" back from 125.213.160.81" The settings I have are:- peer allow=g729&gsm&ulaw&alaw ...
Hi, I am new to asterisk scripting. I used "How to restrict outgoing calls" from "TRIXBOX-2 without Tears" and it works wonderful from the first time. However,...
... hi its me here, i have 1 year working expereince in asterisk communication with PRI and SS7 and call center development solution. as well as hardware...
Hi, I try to make a teleconference room using Asterisk @ Home, however the inbound call always fail to reach 8xxx number. Does anyone know how to reach the...
Hi, I'm sorry, just got the answer. 1. Create an extension, e.g.: 222 2. Call *72, set forwarding for extension 222 to teleconference room 8222. 3. Any call...
Hi, does anybody have an well working Cisco 7970 together with Asterisk? I am looking for someone who is able to create the config-file. The Asterisk itself...
I am using Asterix.I need to use phone extension instead of channel name of the phone for monitor command.Basically,I need to record voice converstaions using...
Hello everyone First time poster, long time reader :) Just wondering if anyone has any advice on best codecs to use for International Phone Calls. I used to...
i keep asking questions and they just disappear, why does this happen, i thought that they may not be Australian enough but others ask non specific Australian...
I am using g729 with 4 PennyTel accounts to call international and its working fine. about your second note, i am note sure but try to add the same trunk twice...
I have an italk trunk, and a softphone, and an ata. Its set up so that incoming calls will ring both the softphone and the ata, after 20 seconds of no answer...
I seem to remember that the hookflash transfer dose work with the ZyXel P2002. I will ask one of my users that uses one next week for you. Is that the silver...
Hi all We have been experiencing problems with our Asterisk and voip provider. The problem is we can not make it work at all. The version we are running is...
The following works fine for me. I use WDP for outgoing landline calls from Sydney to Australian national numbers. Dial Rules: 0+NXXXXXXXX Outgoing: ...
If you really spell "allow" as "alow", then you may not be enabling any codecs for outgoing calls. That could have an effect. ... From: don juan de marco To:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
