Steve, I have 2" x 1" x .25" magnets, lots. Is it possible to use two magnets united to increase the force as a .5" one?...
2332
Steve Spence
sspence65
Jul 1, 2009 5:20 pm
I do not know. Steve Spence Renewable energy and self sufficiency http://www.green-trust.org http://makingthewebwork.blogspot.com/...
2333
gardennut69
Jul 2, 2009 1:42 pm
If there is anyone in Memphis area planning or constructing the alternators, I would like to observe the construction and hear about the planning....
2334
offlogic
Jul 8, 2009 12:49 pm
Your flux will increase with thickness, so stacking magnets will increase the force. Some incidental losses may occur, they they will be very minor. Intermag...
2335
chuck3213
Jul 10, 2009 11:24 am
we have all you need from the magnets, blades, hubs, inverters, wire, batteries and anything else you can think of all for a low price. ...
2336
mmk_tsm
Jul 10, 2009 2:35 pm
Chuck, you wouldnt consider setting up an outlet over here in Europe. Shipping this sort of stuff across the Atlantic gets pretty expensive. Mike....
2337
Dan Fink
danbob88
Jul 11, 2009 3:54 am
I thought that commercial advertisements are NOT allowed on this list? I must've missed you at the national Small Wind Conference in Wisconsin, too. Did you...
2338
Steve Spence
sspence65
Jul 11, 2009 10:30 pm
Commercial advertisements are not allowed, but it appeared to be a link to a source, not someone hawking their own stuff. I allow folks to post links to...
2339
Humberto Javier
hjcg_2001
Jul 22, 2009 10:20 pm
Hi im new here..im actually reading the book windpower workshop. I was looking at the files that you have here and i was wondering if i use the desing of hugh...
2340
Steve Spence
sspence65
Jul 22, 2009 10:25 pm
With careful design, and long enough blades, you can build a 1kw machine. A 100 ah deep cycle battery will provide 50ah reliably for many years. That would be...
2341
Humberto Javier
hjcg_2001
Jul 22, 2009 11:01 pm
thank you spencer so about the magnets is really worth it to buy the n52?? or there isnt a lot of improvement vs n50 magnets...
2342
Steve Spence
sspence65
Jul 22, 2009 11:04 pm
I think you should get as powerful magnets as you can afford. We use the N50's. Steve Spence Renewable energy and self sufficiency http://www.green-trust.org ...
2343
lightning44857
Jul 31, 2009 6:12 pm
on the other power site he is useing .5" plates on the steam engine,would 1" plates be bedder ? and is thair any torque on the stator coils win it is running ?...
2344
lightning44857
Jul 31, 2009 6:13 pm
what size is best should the magnets be large enuff to cover my coil on the stator ? thanks roger...
2345
Steve Spence
sspence65
Jul 31, 2009 6:39 pm
We use a 2" x 1" x .5" Get our axial flux wind turbine ebook at ...
2346
Steve Spence
sspence65
Jul 31, 2009 6:40 pm
not significant. Steve Spence Renewable energy and self sufficiency http://www.green-trust.org http://makingthewebwork.blogspot.com/...
2347
Drew Baden
drew4justice
Aug 4, 2009 10:40 pm
I have all of the rotating parts ready to be mounted on a 4-stud rotor, stator mount, and magnet template.  These are the parts you need if you're serious...
2348
yim tae
tyim999
Aug 4, 2009 10:48 pm
I'm interested.  Please send photos  -Tae Yim ... From: Drew Baden <drew4justice@...> Subject: [axialflux] Got axial flux parts, need to part with...
2349
logicalimprovements
logicalimpro...
Aug 5, 2009 12:36 am
would anyone be willing to provide a wire diagram of the stator for the 1kw generaor project with some instructions on how they wire togather. i have some good...
2350
Steve Spence
sspence65
Aug 5, 2009 12:50 am
Either our axial flux ebook or the dans' book on axial flux wind turbines will give you the info you need. ...
2351
Drew Baden
drew4justice
Aug 6, 2009 3:06 pm
Here are the awaited pics. This set is not powder coated, but as I said, if there is demand for a few other pair, I could powder coat at a minimal charge. ...
2352
Drew Baden
drew4justice
Aug 6, 2009 3:29 pm
Wow! After putting this message out there, I have had an unexpectedly large response.  Instead of replying to each discreet email, I will take pictures...
2353
Keith Goering
kgor
Aug 6, 2009 3:47 pm
I am very interested. Please send photos. Thank you W Keith Goering <mailto:kgoering@...> _____ From: Drew Baden [mailto:drew4justice@...] ...
2354
Drew Baden
drew4justice
Aug 6, 2009 10:36 pm
Tae, Â Did you see my email with the photos? Â Thank you, Â Drew ... From: yim tae <tyim999@...> Subject: Re: [axialflux] Got axial flux parts, need...
2355
inthegutter1000
Aug 9, 2009 1:00 pm
iv seen quite a few diferent picts im wondering if it makes much difference where the coils are placed & how big they are compared to the magnets & how close...
2356
JohnnyO-Paypal
jonellion
Aug 10, 2009 4:55 pm
Is it possible to design a axial flux generator to fit a 12" diameter, be driven by a pulley off of an engine, and produce "X" amount of power at 800rpms ? ...
2357
Nick Andrews
nicothefabulous
Aug 11, 2009 2:40 am
Probably need to stack two or three sets of stators/rotors to get that much power out, but I would say it should easily be doable for you. ... -- Nick A "You...
2358
Drew Baden
drew4justice
Aug 11, 2009 1:44 pm
This all depends on the pulley ratios, right? You should be able to reduce by using a larger pully on the generator and a smaller on the engine.   ...
2359
Steve Spence
sspence65
Aug 11, 2009 1:55 pm
Pulleys will not increase the wattage the unit is capable of delivering, just the rpms. It also affects the blade speeds, as torque requirements change as...
2360
JohnnyO-Paypal
jonellion
Aug 11, 2009 2:19 pm
Anybody want to take on designing this ? I am willing to pay a small fee for someone to tell me what I need to build ..... or I would purchase a pre-made ready...
