... What happens when you rev up the engine? is the alternator on a clutch or something ? Also, getting something homebuilt, so it will pass USCG inspection...
2362
Louis Pelletier
jbunny22002
Aug 11, 2009 2:43 pm
Louis in central BC ... . the rule of thumb is 2 HP PER 1000 WATTS u gonna need a fair size engine to produce that kind of power at an idle Louis in central BC...
2363
Steve Spence
sspence65
Aug 11, 2009 2:57 pm
I've never designed a high voltage unit like that. I wouldn't want to throw a prototype at you. you would need 340 windings per coil, or there abouts, meaning...
2364
offlogic
Aug 12, 2009 1:47 am
The closer the magnets of the rotors are, the better. Vertically thinner coils more than pay for themselves labor-wise and they need to be, at a minimum, at...
2365
jerry freedomev
freedomev
Aug 12, 2009 1:48 am
                 Hi Johnny and All,                          I don't think a AF is right for you though if you want...
2366
JohnnyO-Paypal
jonellion
Aug 12, 2009 1:57 am
Engine is a detroit diesel 453..... plenty of power available at idle. JohnnyO ... From: Louis Pelletier To: axialflux@yahoogroups.com Sent: Monday, August 10,...
2367
JohnnyO-Paypal
jonellion
Aug 12, 2009 1:57 am
Mike - Im just wanting this for when we're hanging on Anchor. It's only going to run a couple of hours at a time. Won't need a clutch. Not worried about the...
2368
coldtags
Aug 12, 2009 2:37 pm
Hi, I was planning on building a system like yours, and I have a question. I cant figure out how you get 3 wires, I can only get 2. The ends of the last coil...
2369
gus_raspin
Aug 12, 2009 2:41 pm
Hello all, I know this is a big question for a first post but I'm planning to build a VAWT to be coupled to an axial flux grnerator. However, I face a problem....
2370
Steve Spence
sspence65
Aug 12, 2009 2:47 pm
there are three sets of coils, 3 coils in series, 9 coils total. you would have 6 wires, the ends of each set of three. One end of each set are connected to...
2371
Steve Spence
sspence65
Aug 12, 2009 2:48 pm
The fourth option is the most common, a diversion load attached to the battery bank. Steve Spence Renewable energy and self sufficiency ...
2372
coldtags
Aug 13, 2009 1:33 pm
Ok I think I get what you mean. I made a little drawning on paint on what I think you mean. Is there a way I can post it up or show it to you in some way? It's...
2373
Steve Spence
sspence65
Aug 13, 2009 1:51 pm
You can create a album in the photo section of the group web site, and post it there. Steve Spence Renewable energy and self sufficiency ...
2374
Steve Spence
sspence65
Aug 14, 2009 2:36 am
Since the Methane Digester Tutorial give away was so popular, we have decided to have a Wind Tutorial give away. Check out the details at ...
2375
Steve Spence
sspence65
Aug 14, 2009 2:38 am
Oops, remove the comma, from the end of the url: http://www.green-trust.org/wordpress/2009/08/13/free-wind-turbine-tutorial/ Steve Spence Renewable energy and...
2376
coldtags
Aug 14, 2009 2:52 am
Ok I put it up under the name coil setup....
2377
Steve Spence
sspence65
Aug 14, 2009 2:56 am
You have miswired the coils. you have three coils in a row in series, it's every third coil. Steve Spence Renewable energy and self sufficiency ...
2378
coldtags
Aug 14, 2009 11:58 am
Im completely lost. can you make a diagram? kinda like the one I made....
2379
indegreen77@...
indegreen77...
Aug 14, 2009 12:23 pm
Steve, Thank you for being so generous with your information. I enjoy and learn from your posts here and on other groups as well....
2380
indegreen77@...
indegreen77...
Aug 14, 2009 12:23 pm
Hi, What program did you use to draw your coil set-up? Can anyone tell me where to find FREE software for a drawing program that does not require much...
2381
Steve Spence
sspence65
Aug 14, 2009 12:41 pm
I appreciate the kind words. Steve Spence Renewable energy and self sufficiency http://www.green-trust.org http://makingthewebwork.blogspot.com/...
2382
G M
mshowdy2000
Aug 14, 2009 1:54 pm
Yes Steve, the freebies are much appreciated. It is never possible to have too much information & knowledge. Always something new to learn. Also, good to...
2383
Neil Dennis
wombat_eagle
Aug 14, 2009 5:03 pm
If you are using Windows, look at "mspaint", can't get much simpler than that. wombat...
2384
Mike Burgess
mike_burgess
Aug 14, 2009 5:38 pm
... http://www.green-trust.org/wordpress/2009/08/13/free-wind-turbine-tutorial/ Dang - that was fast. barely 5 minutes from Request, to PDF's in my inbox. I...
2385
ferrand
ferrandst
Aug 14, 2009 8:07 pm
Controlling rotational speed or sequential charging from an Axial fl Posted by: "gus_raspin" gus_raspin@... gus_raspin Date: Wed Aug 12, 2009 7:41 am...
2386
coldtags
Aug 14, 2009 11:33 pm
Yea it was just simple Microsoft paint. if your running a windows it brings it standard on all comps. its as simple as painting with a mouse gets....
2387
Steve Spence
sspence65
Aug 14, 2009 11:41 pm
I'm not on microsoft, and don't have a convenient paint program available, but it's easy to describe. You have 9 coils. connect coils 1, 4, and 7 in series, 2,...
2388
coldtags
Aug 15, 2009 12:21 am
OOOOO I get it now. wow took me a while. Awsome thanks a bunch man, couldn't have figured it out with out you. I'm goin to order the copper wire and get to...
2389
Steve Spence
sspence65
Aug 15, 2009 12:22 am
I have the 3 phase rectifiers in stock when you are ready. $35 Steve Spence Renewable energy and self sufficiency http://www.green-trust.org ...
2390
imran sipra
imran_sipra
Aug 15, 2009 11:31 am
hi dear i need ur help to design charge controller for battery bank 48v @50A could u help me Engineer imran nazir  hi dear i need ur help to design charge...
