... Just as a follow-up to this thread, I read an interesting article today: <http://www.technologyreview.com/Energy/20500/> Seems like Slade is not alone :) ...
Dave Howorth
dave@...
Apr 2, 2008 8:24 pm
1155
Hello all, I have just saw within the Catalyst number 28 that Michael Bedwell needs a single oar sculling original solution. Perhaps that what follows will ...
... Hello Tony, Thank you for your answer. The system show from your link is not the same as the godyoto I present above. The Doi Atsushi japanese Ve-scull...
... Bonjour Guy, ... Doi san took the ro and turned the blade 90° (he is a retired 747 pilot from Japan Airlines and had lots of time to think on those trans...
The AYRS May meeting is being held at the Castle Cove Sailing Centre, Old Castle Road, Weymouth form Monday 19th to Friday 23rd of May. £30. for tea and...
Hello Tony and all, ... [..] ... Yes, and it is needed too for the whole system works fine with the incidences as the vertical disposition needs it. I know as...
Hello, Robert! ... Yes, you are correct: the original sentence (used to check typewriters) was: THE QUICK BROWN FOX JUMPS OVER THE LAZY DOG ... Because I want...
Curiously, when I go to the "Files" are of the AYRS Yahoo Group, then click on the file "UTFTEST4.UTF" of "Mr.Emmanuel_Roche", all the characters are displayed...
Well, I really don't know what is happening. When I publish this HTML file in this Yahoo AYRS group, it displays the values of the characters, but don't show...
... May be the same concept : http://www.sea-quad.com/ Best, -- Guy Capra _________________ www.alomphega.com www.conceptarum.com www.nauticaerium.com...
Guy Capra schrieb: ... That's quite impressive, especially the kite-sailing video! Solves the kite lauching problem, provided you have a flat beach handy and...
... lift ... varying ... same ... air "leaking" ... the ... ship ... a famous work regarding the Flettner rotor. Was that just fun or missunderstanding all...
Does anybody have an easy technique to make turbine blades [like a wind-generator might use] with approximately the proper twist and taper? [balance and...
G'day, I built mine (3 x 4.6m) from plywood and fibreglass in female mdf mould framess. Pretty easy although the leading edge had to be done with templates....
... I cut out profiles (wing section) from styrofaom and put these together on and glued them too an aluminium tube in the correct twist. Then sanded them...
Hello all, I'm happy to tell you that my last try of the "Godyoto" (single automatic oared sculling system) worked as well as possible ! :-D You can see the...
On two occasions sailing my Dory-hulled catamaran in 15-20 knts. winds, it accelerated just like my Flying Dutchman did when going on the plane. Very exciting...
Ian Your dory hull must've had a pretty wide flat bottom, and hard chines. Why did it take in so much water-spray, like, was it blowing back aboard the lee...
Guy Capra schrieb: ... Thank you, Guy! I am more in need of translating the video format, all I get is a black box even though I have the Flash player...
... Normally the same as YouTube Theo :-/ Try it directly may be it will be good : http://www.dailymotion.com/video/x570wl_20080424-1er-essai-godyoto_tech And...
... Here are "my 2 cents": 1) The video is much too long (19 minutes 39 seconds...). I suggest to use the format used commonly by musical videos: 3 minutes....
Le 28/04/2008 10:09, roche182@... inscrivait : [..] ... Thank you for the course Emmanuel, but I suppose some people would just like to see a maximum...
