Hey Tracy, yes, esoteric is the word... I must admit that I donot understand one single line of your code which might partly change after I will have read the...
I'm not sure if this will help or not. When you connect the BS2 you should have caps for your serial cable. One goes from pin 4 on the serial cable in series...
The OEM version of the BS2 has those caps on the board already...
Pepsi
pepsi@...
Aug 1, 2002 7:24 am
23578
... From: ulibasic <ulibasic@...> To: <basicstamps@yahoogroups.com> Sent: Wednesday, July 31, 2002 1:39 PM Subject: [basicstamps] inA and...
Klaus Zahnert
kzahnert@...
Aug 1, 2002 10:24 am
23579
I am tring to design an Eddy current detector for shaft runout. I have been successful in being able to detect the linear distance to the shaft. However I can ...
Greetings! Anyone know if there's any plans for a low voltage BS chip? 2.5V to 3V would be grand... (I'm working on a VERY small project, and batteries are...
Ok, this should be simple and I have seen the circuits that allow relay control, yet I would like some little peace of mind that 300 amps aren't going to end...
We've had no discussions about building a low-voltage Stamp. I think, for the time being, that would not be a fruitful project for us. Despite appearances,...
Optical isolation with separate power supplies is going to be your best bet. -- Jon Williams -- Applications Engineer, Parallax In a message dated 8/1/02...
I'm new to BASIC Stamps, and I have just recently received my BASIC Stamp Rev. D. starter kit, and I want to know how I hook up an LED to the prototyping area?...
James Simpson
basic_stamp@...
Aug 1, 2002 2:23 pm
23585
I would sincerely suggest you get a copy of Scott Edwards' book: Programming And Customizing The BASIC Stamp Computer. Not only will it help you with ...
You can make the connectors pretty easily. However, I prefer to buy them: http://www.elexp.com/bb_0mf1.htm The female to female will plug into those pins. A...
Hi Uli, ... Wow, scary, doctor! The problem is, there are so many possibilities. If you need to consider every possible combination of 12 buttons, there are...
Excuse my ignorance but let me get this straight. I'm still not clear on how you would connect everything together. Basic Stamp I/O pin <- female-female ->...
Paul M
basic_stamp@...
Aug 1, 2002 6:19 pm
23590
Unfortunately, I don't know any other places that sell these ready made. Most people make their own with heat shrink and "pins" that you can buy for making...
how to locate my robot in a range of 50 meters? the bot it is based on a bs2sx. i need to determine the exact position of it (+/- 10cm) in a football stadion. ...
Hello, I recently purchased these RF modules from Rentron. I am trying to use them with the older Holtec HT 12D & HT 12E encoder & decoder chips. I am having...
... Contact me at this email address tech@... and we'll get you going. These can be used with pretty much any encoder/decoder ICs', but there are a few...
Trygve The BS1 is based on a PIC16C56, which does not have a brownout detector built in. That chip is supposed to operate down to 3.0 volts at 4mhz. I see no...
... Not exactly "push"... more like "overshoot" ... Beau Schwabe Mask Designer IV - ATL National Semiconductor Enterprise...
Beau Schwabe
bschwabe@...
Aug 1, 2002 10:50 pm
23597
... Heck! Why not a speaker? 1/4 inch travel 4 Oz shouldn't be to difficult. ... Beau Schwabe Mask Designer IV - ATL National...
Beau Schwabe
bschwabe@...
Aug 1, 2002 11:01 pm
23598
That's a great Idea, If you need more travel just hit it with a couple thousand watts, one time use only. ... From: "Beau Schwabe" <bschwabe@...> ...
Larry Gaminde
lgaminde@...
Aug 2, 2002 1:08 am
23599
I was at www.tannerelectronics.com recently and they had a box of push solenoids on the shelf there. It looked like they had about 1/4" of travel to them. But...
I would agree. Look at digital I/O devices from Crydom, OPTO-22, Magnecraft, etc. They all have output modules rated for AC and DC loads. I do this stuff with...
Working on a project where I need some help with finding a source for white LEDs. I am specifically looking for some discrete white LEDs (preferably T1-3/4...
HI GUYS, ANYONE SEEN ANY SCHEMATICS AND/OR CODE LISTING FOR A SIMPLE METAL DETECTOR USING A BS2? HELP APPRECIATED THANKS AGAIN MIKE M [Non-text portions of...
mocenter
mocenter@...
Aug 2, 2002 2:53 am
23603
I had gotten some white LED's from www.digikey.com a while back. I also had bought some off of www.ebay.com a while back too. ... From: digital_interior...
Hello from Gregg C Levine Not yet. But I've got one request. Cease and desist from using all caps, its considered shouting, and its rather rude, and very...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
