I'd like to use the transmit only capability of COM3, and it appears that DefineCom3 allows one to specify pin 0 as a dummy input pin. Does that also mean that...
16689
naimead
Aug 1, 2004 4:31 pm
Hi all, Has anyone before managed to handle oopic's DS-GPM gps system using BasicX microcontroller? thanks...
16690
Ryan Johnson
ryanjfjohnson
Aug 1, 2004 4:31 pm
If anyone has any insights I would be very appreciative as its for a school project and If it turns out to be fried I would be a little dissapointed as it did...
16691
#@!%! Herzog
hwanghetw
Aug 1, 2004 7:12 pm
I just started with the BX-24 and have been reading several e-mails regarding sudden failures. I have a 9-volt 'wall wart' that I was preparing for use, but...
16692
Tom Becker
b19063
Aug 2, 2004 3:50 pm
BTW, the BX-24 interrupt latency is on the order of 100-150uS. I don't think I've ever seen that expressed. Tom Tom Becker --... ...-- GTBecker@......
16693
naimead
Aug 2, 2004 4:44 pm
Hi, -Does BX-24 works good with other microcontrollers like oopic or basic stamp?If yes how can be connected together? -Also why does it consume so much...
16694
cmos8me
Aug 2, 2004 6:35 pm
... devices,isn't ... Yes it does work good with other MCU's using serial communications, and for the latter it does not consume more power than others, it ...
16695
Chris
robotlogic
Aug 2, 2004 8:24 pm
He left to pursue his interest in aerial robotics. I think it was with the U of A. Chris ... From: "William Chan" <william@...> To:...
16696
Don Lewis
bubba_0n_wye...
Aug 2, 2004 10:08 pm
I will toss in that the BX-24 is 5V ttl compatible where many other newer controllers are 3.3V with some TTL input compatibility. The BX-24 has an on board...
16697
Don Lewis
bubba_0n_wye...
Aug 2, 2004 10:10 pm
Just a thought... Low voltage monitor To prevent the BX-24 from locking up or running erratically during power-on or any other periods of transient or low...
16698
psyclopedia
Aug 3, 2004 1:35 am
So does this mean that there is no representative for NetMedia watching the forum? That's a shame. It's always nice to have access to someone 'in-the-know' ...
16699
Tom Becker
b19063
Aug 3, 2004 2:08 am
... Well, there's Chris, the guy that just told you where Frank went. Tom Tom Becker --... ...-- GTBecker@... www.RighTime.com The RighTime Clock...
16700
Thad Larson
highwayman_3...
Aug 3, 2004 11:45 am
And the future of BasicX ? Is the Beta version a real possibility? Thad ... __________________________________________________ Do You Yahoo!? Tired of spam?...
16701
Don Lewis
bubba_0n_wye...
Aug 3, 2004 4:43 pm
Yes I am ready to buy more of something. I have been learning the bx-24 since about last christmas. I learned it has it's good and bad. If NetMedia is planning...
16702
naimead
Aug 3, 2004 6:06 pm
Thank you for the answers.So i suppose that if i use a 5V battery on an autonomous robot it will work fine?...
16703
hannesnehls
Aug 3, 2004 6:06 pm
it is something like THE newbie question number one but anyway whats happening to me seems strange to me. when i plug the bx24 to my breadboard driven by a...
16704
Bob Roos
wybatap
Aug 3, 2004 7:49 pm
Check your ground connection between the PC and the BX-24. Also when you say that it gives everything you want to the serial do you mean that it sends from the...
16705
Chris
robotlogic
Aug 3, 2004 10:51 pm
To All, We at NetMedia are actively working on newer versions of both the BasicX hardware and software. After an extensive review of the BasicX product line...
16706
p_dubinsky
Aug 3, 2004 10:52 pm
Does anyone know how long a GetADC command takes? Would it be faster to use an off module ADC (assuming 10 bit resolution)? Thanks, Paul...
16707
Chris
robotlogic
Aug 3, 2004 11:16 pm
A floating point GetADC takes 278 us, an integer GetADC takes 164 us. Chris ... From: "p_dubinsky" <pdubinsky@...> To: <basicx@yahoogroups.com> Sent:...
16708
Paul Dubinsky
p_dubinsky
Aug 3, 2004 11:36 pm
... Thanks. I assume that the difference is the floating point conversion overhead. Paul ... =========================================================== "We...
16709
William Chan
william@...
Aug 4, 2004 12:22 am
Isn't it time for NetMedia to launch a new BasicX processor? The BX24 is getting old... William ... From: "Tom Becker" <gtbecker@...> To:...
16710
Leddy
dlpreuss
Aug 4, 2004 5:34 am
I'm trying to decipher the max input current the BX24 can handle. Is it 15mA per pin 70mA total? It's labelled as "output sink current" Care to shed some...
16711
Neil Jepsen
neil_jepsen
Aug 4, 2004 6:12 am
Output sink current means each output can "sink" i.e "switch to ground", a load which pulls 15mA from the +5 supply. Hence the load must be connected between...
16712
daliti
Aug 4, 2004 9:47 am
Hello, I'm looking for a Basicx programmer for a project of a pressure testing device. I'm not necessarily looking for a professional or a full-time ...
16713
Raymond Irving
xwisdom
Aug 4, 2004 2:28 pm
Personnal I would like to see a BasicX with more RAM and ability to read and write to flash card, or USB pen drives. You also need to start working on...
16714
hannesnehls
Aug 4, 2004 5:31 pm
thanks bob. the ground fixed it. cheers. hannes. ... do you ... you are ... transmit ... <hannesnehls@y...> ... whats ... cant, ... at ... is ... the ... Igoe...
16715
chicoisl
Aug 4, 2004 11:29 pm
Hello, Is there more information about the ShiftOUT and ShiftIN commands, more then the System_Library.pdf provides? I am trying to use these commands in a...
16716
wurlitzer28
Aug 4, 2004 11:29 pm
Please Chris, don't tell me that you are dropping support for VB6! It is the sole reason I am using the BasicX series. The editor in VB6 is either very user...
16717
chicoisl
Aug 4, 2004 11:41 pm
Thad, Thankyou for your reply... Yep, im using pin 19 as the clock and pin 20 as then data, these are labeled SC and SC in the BYORK schematic. Yep, in BS2...
