Hi, I'd like to be able to control 90 LED's individualy with a bx24. I know there are some ic2 IO expanders as I've seen other projects using them. I was...
Paul J. Smith
pjsmith@...
Jun 2, 2008 11:36 am
22824
I have build a circuit that lights up to 48 leds. 6X8 matrix. I used the BX24 to source 6 rows and 8 to sinc. Ofcourse I can only light one led at a time as...
Hi, I've used a chip TC4094 to create a large number of outputs using just a clock, data, and strobe lines. Essentially you feed your bit pattern serially...
Hi, There is a max6969 serial? four line interface with 16 led output driver. I never used it but you can look at it. You can daisy them to get 90. rosarite? ...
I have used a few different ones, the one that I prefer now is the proto24 available from pcboard.ca at this link. http://www.pcboard.ca/Kits/Proto24/ ...
I'm working on an ECU reader project, that require serial communication on 10400 Baud. But standard OpenCom procedure offer only standard rates - 9600 or...
... I have worked with analyzation of accelerometer signals and also made simulations and analysis of the signals. As I imagine the issue will be to avoid...
Hello, This is just an update on my project. I went with the multiplex idea. I used two of the 4051 and hook analog pins to each of them. I also hooked 3 I/O...
Folks, after experiencing a fortunately-minor heart attack last Saturday that put me through two hospitals in five days, I want to reduce my unnecessary...
I wish a completely good recovery and good luck. We are going to missed you. rosarite ... From: Tom Becker <gtbecker@...> To: basicx@yahoogroups.com ...
Best of luck, Tom. Welcome to the world of "mostly lurking". Stop by and say "hey" once in a while. Thx for all your work over the years and, again, best of...
May God Bring you all you desire! To: basicx@yahoogroups.com From: rosarite@... Date: Sat, 5 Jul 2008 17:38:32 -0400 Subject: Re: [BasicX] With kind...
Hi Tom, Thanks for the wonderful contributions you have made to this group over the years. I hope and pray all goes well for you. Thanks and Regards, Ian P.S....
Tom, Thank you for your support of the BasicX group, you will be missed! I've been working on other projects at NetMedia and haven't been putting the time I...
Hello! ... I'm also trying to get the EB500 to work with the Basicx. I do have the led lighting up on the EB500 indicating a connection. This is what I found: ...
Digging through some old notes I found this graph that someone might find useful. http://tech.groups.yahoo.com/group/basicx/files/BX24/ BX24_TvsF.GIF Tom...
Hello, I would like to know what would be the best approach to switch a 2 to 3A, 24Vdc load on and off using the basicx 24. I have looked at a transistor but I...
Hi, You can use a mosfet transistor with a transistor between the BX 24 and the mosfet as isolation or like you said a relay but a solid state relay. You can...
Switch a relay coil using a transistor. Like here: http://www.wam.umd.edu/~toh/ElectroSim/relay.html ... [Non-text portions of this message have been removed]...
You may be right about using a relay. Short of using an amp to drive the correct transistor I was wondering if you could do the switching in the AC mode. I...
What is the load? Two or three Amps isn't difficult at all if it is a resistive load, a little more difficult if it is an inductive load. I PWM an 8-Amp 12v...
Thanks everyone for the input. I decided to go with a solid-state relay similar to the omron g3tc series. It is designed for microcontrollers. FlyerX...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
