Group, I have noticed that when I use the Pow() statement in a task the task locks and the program stops running. Here are the details: I have used a Sharp...
Group, I used a 30 byte stack.Slowing down did not help.This problem is not seen when I use /,*,+,-.Only seen when Pow() or ^ is used. Is 30 byte stack...
... There is a good chance that's insufficient. Try increasing it, first generously; if your code starts working, then trim it back until you run into trouble...
Hello guys. I would like to know if you can suggest me any antenna for exterior to work with basicx24? specifications: - 400m range minimum; - Resistant to...
... humidity) What is the FREQUENCY of the transmitter and what are the limitations of the antenna installation? Do you need a: 50' tower? 6" of wire? 8...
Also: fixed/mobile, data rate, maximum permissible error rate, power requirements, electronics-to-antenna cable length, cost? There are many options, but you...
Hello all, I have a question regarding my latest project, I need to use a pump that sends very small volumes of gas inside a tube and removes the same ammount...
The frequency is 433MHz, 868MHz or 2,4GHz. The antenna will be fixed at a refuge house's roof, 9600bps or less, preferably 12V power, 4m cable between the...
Does anyone know how this is done? I want to put the cpu into idle mode using an interrupt from the the compare function on timer 1. According to the Atmel...
I have a issue in using of COM1, COM3 and Pulseout. So, I intend to use SPI to receive data from other source. Is it possible to use SPI of BX24 as a COM port....
Hi everybody, I have question about seperating a pulsetrain into individual channels. I use the outputcapture to generate a pulsetrain that consists 4...
... A shift register can do that. Use the output capture clock pin to clock the shift register and feed your composite data pin to its serial input. Each...
Thanks for your suggestion. I found a shift register namely MM74HC595. Hope that I can reach this device this afternoon, so that I can try PWM seperation. ...
Hi Tom, Can I ask about the Output capture clock Pin. I look at the description of BX24 Pins, but I could not find the Ouputcapture Pin. Can you help me. ...
... It is any I/O pin, assigned in the OutputCapture instruction. If you connect it to the shift register clock, the data will be placed on each output pin in...
Hope that Ouputcapture and Shiftout use the same clock. I have written a code as follow: Public Sub mani() const clock As byte =10 ' connect pin 10 of BX24...
Hi all, I am looking for an encoder for DC motor. Could anyone give me some suggestion about which the encoder I should us for my DC motor. the maximum output...
Can anyone please suggest some antenna or a company that sells anything with the specifications that I gave to you at the last post? regards Hello guys....
i'm new to this device. i'm going on a project to determine position using accelerometer. however, i found out that many errors will occur. is it possible to...
All antennas meet the requirements below, however, the transmitter and receiver would limit the distance the antennas are usable over. The antenna cover, or...
I should have clarified... RAPIDY water-soluble metal, like paper-mache or mud... You might want to try cutting a paper-clip to the operating frequency for ...
Hello Everybody, I am interested by everything related to the BX-24 family and for this post, I do not see the relation between our subject BX-24 controler and...
Hello Everybody, I am interested by everything related to the BX-24 family and for this post, I do not see the relation between our subject BX-24 controler and...
The original poster most likely wants to send data from a BX-24 to another BX-24 over an RF link. He asked about an antenna, but provided no details of the...
Hello Everybody, I am interested by everything related to the BX-24 family and for this post, I do not see the relation between our subject BX-24 controler and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
