Hello guys. I would like to know if you can suggest me any antenna for exterior to work with basicx24? specifications: - 400m range minimum; - Resistant to...
i'm new to this device. i'm going on a project to determine position using accelerometer. however, i found out that many errors will occur. is it possible to...
Hi, I would like to find out how can I interface 2 D.C. motor with their respective encoders to basicx to both perform some sort of velocity and position...
Hi everybody, I have question about seperating a pulsetrain into individual channels. I use the outputcapture to generate a pulsetrain that consists 4...
I have a issue in using of COM1, COM3 and Pulseout. So, I intend to use SPI to receive data from other source. Is it possible to use SPI of BX24 as a COM port....
Does anyone know how this is done? I want to put the cpu into idle mode using an interrupt from the the compare function on timer 1. According to the Atmel...
Group, I have noticed that when I use the Pow() statement in a task the task locks and the program stops running. Here are the details: I have used a Sharp...
Folks, I've been away from the BX-24 for awhile but am getting ready to start a new project. I need some advice on a display. This will be mounted on a ...
Hello everybody, To measure the current in my 3 phases house electricity system and in the neutral, I am using 4 Honeywell Current Sensors CSLA2CD powered with...
Hi I have not been able to figure any good explanation of how BX can avoid getting the program instructions cluttred when the SPI bus is used. BX24 is fetching...
Hello Everybody, In my program top read a current, I have declared the following: Dim I1 as Single Dim V1Max as Single And them I do something like that: ...
After working several times with DefineCom3 together with OpenCom(3, ...)some questions arise: Imagine we have this piece of code: Call DefineCom3(16, 17,...
Hi there im new on this world, so im sorry if im saying something wrong or senseless. I have 2 sensors, one is getting the moistness and the other is getting...
I was trying to connect a ultrasonic sensor (SRF08) to the development board with a BasicX 24P on it, and the BasicX suddently stopped working. I was using...
Hello World of BX-24 ! I have written this little program to control X10 appliance connected to B3 House Code Device code. The BX-24 is connected to an...
I just pulled out a kinetic sculpture I built 3 years ago. It's controlled by a BX24. I plugged in power and got absolutely nothing. I seem to remember hearing...
Hello, I wrote the following program to read a value on the ADC Port and convert it to RMS value. I have an error at the line Next K and I cannot find the...
Netmedia's Chris is clearly busy designing exciting new products and does not have time to effectively moderate here. If you guys read a question that you can...
Hello, I want to read 4 AC voltage at 50 Hz coming from a Current Sensor using the BX-24. The BX-24 (or other type of processor) read only DC voltage but the ...
Does anyone know the current production status of the BX-24 and related modules? I have a couple of new gadgets in the works and since I haven't seen much...
Hi, I recently pulled out my BX-24 to do a thermostat project. My youngest son expressed a desire to do an electronics project that would include programming....
Hi Everybody, I've messed with Basic Stamps for a while and have upgraded to BasicX products, primarily the BX24 Development Station. Unfortunately, I'm...
Hello, I would like to come back on this issue of X10 Command with BasicX- 24 because I have a lot of problem to find the proper support and proper answers to...
I'm just coming back to my BasicX-24 having dabbled with various other controllers, corrupted disks and various other events... I remember problems with...
I am trying to get a simple X10 test program to work but the program seems to crash in the X10Cmd. I am using a X10 PSC05 powerline interface and AM14-A...
hi, I pulled out my old BX24 to play with controlling a servo, and I am having some problems with it. I have a both a regular analog servo and a new digital...
Hi, I was trying to install basicX enviroment but it hangs after starting setup.exe with no message at all. My system: WinXP home SP3 2Gb RAM Laptop Toshiba...
Hi guys, I am new to using control circuits, but understand the basics. I have a few questions about a project I am working on at school. We are designing an...
