there are ways of fixing that. Anyhow: Potential new discussion: consider the B.I.O. Bugs. These mailing groups permit some pretty wide-ranging points of...
34
cybotbuilder
Feb 27, 2002 6:16 pm
Hi all. I'm quite new to BEAM. I'm attempting a 1 motor walker which uses a bicore. It's taken from the Insectroides web site. My robot walks for about 3...
35
Thomas Pilgaard Nielsen
ascii_2001
Feb 27, 2002 9:26 pm
... it !might! be a result of motor noise. Do you have your high-frequency filter caps applied across the power rails of the 74**240 as well as across motor...
36
Andrew Spaxman
cybotbuilder
Feb 28, 2002 2:56 pm
... wrote: it !might! be a result of motor noise. Do you have your high-frequency <BR> filter caps applied across the power rails of the 74**240 as well as...
37
Thomas Pilgaard Nielsen
ascii_2001
Mar 1, 2002 12:11 pm
... What don't you think Andrew? That it may be a result of motornoise or haven't you applied any HF caps? Cheers, Thomas ... INSTRUCTIONS: For results that...
38
John A. deVries II
ztfreep
Mar 21, 2002 6:14 pm
... Hokay The Automatron... please post a note that asks a question about bicores in some way or talks about a bicore idea that you've had. I realize that...
39
the_automatron
Mar 25, 2002 11:28 pm
... about ... I ... would be ... hay i wasnt even checking messages, sorry.. me just a noob, working on a one motor walker tell the rest of the chips show...
40
John A. deVries II
ztfreep
Mar 26, 2002 12:39 am
... That's OK. I often find that I miss them even when I -am- checking! ... Nope, not a noob because you -did- write. What sort of one motor walker are you...
41
Wilf Rigter
wilf.rigter@...
Mar 29, 2002 10:16 am
Hello Automatron, Do the legs/ move in the horizontal or vertical plane? The horizontal motion is like a aligator always pivots around the foot on the floor...
42
the_automatron
Apr 2, 2002 4:24 pm
i dont have the legs hooked on yet, just to a stepper motor.. wanted to se how far they turn first......
43
the_automatron
Apr 2, 2002 4:27 pm
is there any way to use infrared detector on the light seeker head?...
44
chasey_david
chaseydavid@...
Apr 2, 2002 10:00 pm
Hi, I work for Children's Hospital of Pittsburgh. The anesthesiology and pulmonology departments are doing some research using a piece of bicorre equipment...
45
the_automatron
Apr 9, 2002 2:25 am
i guess it was the wrong chip... put in diferent one and now it doing it right.....
46
John A. deVries II
ztfreep
Apr 10, 2002 4:58 pm
... I am confused. What circuit / device were you working on? I seem to have missed that somewhere. z...
47
the_automatron
Apr 12, 2002 9:49 am
im using this circuits, http://roboticarts.netfirms.com/Images/photobicore.gif 2 .22uF capacitors (digikey part # = P4958-ND) and around 5volts. my chips keep...
48
the_automatron
Apr 12, 2002 9:50 am
it was a post I did awhile back.... http://roboticarts.netfirms.com/Images/photobicore.gif...
49
John A. deVries II
ztfreep
Jul 22, 2002 7:06 pm
Hello sandroid, I see you've joined the bicore list today. If you have any ideas at all about bicores, or if you have any questions, PLEASE post a message or ...
50
Alex Roy
sandroid2000
Jul 22, 2002 8:12 pm
thank you for the warm welcome! i recently joined all the groups related to beam posible, so as to speed up the learning process. im going to read all the...
51
Alex Roy
sandroid2000
Jul 26, 2002 1:02 am
what will it sayon the pinout of a chip to signify that it has an inverter(schmitt or otherwise). will it say inverter in, or out, or will it say somthin'...
52
Alex Roy
sandroid2000
Jul 27, 2002 9:21 pm
i normally buy my beetlebot motors(ive got two built now!) from radioshack for 3.99 apiece. but i went over to the dollarama(i dont know if their an...
53
Alex Roy
sandroid2000
Aug 1, 2002 10:20 pm
i've heard if a device meant for newbies to soldering, called a heatsink clip, it attackes to whatever you are soldering to draw heat away from it to prevent ...
54
Skywatch
skywatch@...
Aug 3, 2002 8:54 pm
Another trick is to attach a crocadile clip to the lead you are slodering (between the soldered joint and the component itself). This should allow the joint to...
55
Your Friendly Hogfather
ztfreep
Aug 3, 2002 9:27 pm
I just looked at the RatShack catalog (www.radioshack.com) which has a likely candidate... and not too great a strain on your budget, I hope! ... Odd though,...
56
Thomas Pilgaard Nielsen
ascii_2001
Aug 4, 2002 7:31 am
When I travelled acress the US last year I was fortunate to find one at Radio Shack (yeah yeah I know) for about a couple of bucks as far as I remember. I am...
57
Alex Roy
sandroid2000
Aug 7, 2002 9:08 pm
i finnally got parts for my FLED SE and ample parts for a fred or two..except for photodiodes! i asked for photodiodes, the guy laughed a little, pulled out a ...
58
Alex Roy
sandroid2000
Aug 12, 2002 12:20 am
i currently dont have access to any inverter containing chips and i hope to build an inverter of my own untill i get one. so ive worked out this schematic(in...
59
Wilf
wrigter@...
Aug 12, 2002 12:46 am
Sorry Alex, but making your own inverter that is compatible with BEAM circuits like a microcore or bicore is not practical. For interest the PNP in the circuit...
60
Alex Roy
sandroid2000
Aug 12, 2002 4:31 pm
Do you ... why yes i do!(pandoras box has opened) i have many that i haven't been able to identify thus far and some that i dont know if they are ICs or not! i...
61
Alex Roy
sandroid2000
Aug 15, 2002 5:07 pm
back in july i asked the OT question of, "are there other celebrations similar to Canada Day(July 1) and Independance Day(July 4<US>)?" and i got many answers ...
62
Alex Roy
sandroid2000
Sep 4, 2002 6:07 pm
i just got back from my very first day in high school! [applause] and i realized that all my messages from the last three days were deleted by accident, so if...
