hi guys i am in need of ur help i am building my first robot and the competetion is robowrestling i am in need of circuits or the components i would have to...
Hi, Could anyone share schematics of a Mega64 and a drive circuit for a unipolar stepper motor. I went through the book but I could understand much from the...
see Unipolar Stepper Circuit <http://www.arduino.cc/en/Reference/StepperUnipolarCircuit> I use the 2 wire schematic with ATMega8 and it works flawlessly....
can anyone recommend some software to directly burn the code into atmega32 instead of first using a simulator? also does anyone have the tools required to...
I suggest you download the Atmel AVR Studio which is free. It is very easy to set the various clock settings such as external crystal/resonator or extrnal ...
simple and cheap parallel port device programmer <http://www.arduino.cc/en/Hacking/ParallelProgrammer> best AVR firmware/fuses/locks burning software ...
hello, i need to burn a program into the at89c51ed2 controller.please give me the schematics of a programmer to burn a program into its flash memory using the...
There's an interrupt vector usually at address 0x0000 in which you must specify what to do upon reset. That's usually a jump to the desired program address....
thank you very much for you reply. Could anyone suggest a wireless module and how to connect it to the Mega64 in order to get 802.11b/g network? thanks in...
hi all, i urgently need the information regarding how to amplpify the voltage.. avtually my input voltage is ard 5 mv ard and i want to amplify this to drive a...
use noninverting negative back op-amp lm324 gain=1+Rf/R deepu_iiitj <deepu_iiitj@...> wrote: hi all, i urgently need the information regarding how to...
Do anyone have manual of C35/S35 or any? I want to communicate mobile with AVR MCU. Engr. Kishwar Kumar | Cell : +92-333-2742818 | sansain123@... ... Get...
only i have the schematic diagram and i don't know the protocol for this cell phone Sami Z Saqqa Master in Communication Engineering Electronics Eng. ...
You can find lots of Siemens Service Manuals here: http://www.eserviceinfo.com/equipment_mfg/Siemens_10.html Ciao Peter ________________________________ Von:...
... I see. So you may need this: http://alumni.ipt.pt/~pmad/s35i_c35i_m35i_atc_commandset_v01.pdf But I don't know what the difference between S35 and S35i and...
Thanks buddy :) ... I see. So you may need this: http://alumni.ipt.pt/~pmad/s35i_c35i_m35i_atc_commandset_v01.pdf But I don't know what the difference between...
Thanks buddy :) ... I see. So you may need this: http://alumni.ipt.pt/~pmad/s35i_c35i_m35i_atc_commandset_v01.pdf But I don't know what the difference between...
hi,I need help my graduation project contain PIC18F4520,2-digits seven segments, 16key keypads. how can i programming this PIC and display the number that...
Hello everyone, I am on the look out for making Distance Calibrating Sensors. I want to make these sensors using IR emitter and reciever (either photodiode or...
ajay for ambient light issues you can use 40khz modulated ir transmitter and reciever pair used in tv remotes, and easily available in market. or you can make...
Prateek I have checked these modulated recievers you are talking about ( I think you are talking about TSOP or something similar) but these give me digital...
Hi All, These sensors are very difficult to make as in case of Infrared sensors u r using light to measure distance.so here ur constraints are :- 1 U cannot...
my project z abt ultrasonic parking cotroller bt there z a problem abt the selecting of software for its programing bc in my project i m using (atm Mega 32 )...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
