Richard, ... panels, I thought you may be doubling up as you suggest with the MDF. The 15 1/4" panels needed to be cut to fit. The other HB panels slot in fine...
... Hi Bob I thought I would enclose a few links of the build so far… For those of you based in the UK the following adhesive appears to be suitable for...
... ********************************************************* G'day Bob! Can you keep up with these posts? Would you mind checking this insulation before I...
Hi Bob I hope your HIFI show went well last weekend! I am nearing completion and have a couple of quick questions if you have a moment. Port length I am using...
... It went very well. There are some pictures posted at <http://www.audioasylum.com/index.html> http://audioroundtable.com/forum/index.php?t=thread&frm_id=2&...
... Hi Bob I have just spotted this cheap round over bit on ebay...I will probably only use it once so it's not worth spending too much. I might be able to...
Richard, I have no idea what a good router bit should cost you in the UK. I pay ~$25 delivered for my 3/4" round over bits and they are of so-so quality. From...
Made a few changes to the web site.: Had to up the prices again to cover increased materials costs. But note -- shipping is included in the price. I split the...
Bob, As you know I built the LT-2000 speakers from your plans a couple years ago and have been using the DX-3 driver. Concerning your cabinet dimension change...
Jim, The acoustic results of reducing the cabinet depth to 10" from 11 1/4" is subtle. There is no reason to build new cabinets. If I was mass producing...
Hi It was difficult to find your email address, the address on your site does not work. Can you give me some typical prices of the speakers you have listed on...
hshel1
hshel1@...
Aug 5, 2009 12:02 am
152
Hi Please email me at hsheldon@.... Regards Howard...
hshel1
hshel1@...
Aug 5, 2009 12:02 am
153
Bob, I have the LT-2000 (pre-Mk II format) which I have not yet finished and it is not sealed. I'm up and running now (finally). I want to be able to emulate...
Monte Bedford
mbedford1@...
Aug 5, 2009 4:17 pm
154
... Clarification. The Hardi-Backer has not been cut, so I am free to: cut to different dimensions add more Hardi-backer add more wood I wanted to make this...
Monte Bedford
mbedford1@...
Aug 5, 2009 4:30 pm
155
Howard, The email address rbrines@... on my web page is correct and operating. AOL may be blocking the domain. They do that to third party ISP's. I...
Monte, ... The difference between the MkI and MkII cabinets is the depth is reduced form 11 1/4" to 10". Since you have all of the wood cut, the easiest way to...
Just some notes on my experiences. Fiberglass board. This worked out well--better than expected. Look for heating/air (HVAC) supplier or ask your heating/air...
Monte Bedford
mbedford1@...
Aug 6, 2009 7:18 pm
158
Just some notes on my experiences. Fiberglass board. This worked out well--better than expected. Look for heating/air (HVAC) supplier or ask your heating/air...
Monte Bedford
mbedford1@...
Aug 6, 2009 9:58 pm
159
Bob, have you considered whether either of these would work in your existing enclosures? The 1772 doesn't seem too different from the Fostex 207. It would be...
Fred, The W8-1772 models as a drop-in for the FE207E in the FT-2000 cabinet. The TB starts to roll off a bit earlier in the bass than the FE, which is actually...
Back to my speaker project after way too long of a diversion... Alas, all I can find locally for Armstrong #420 is the commercial equivalent #2911 at...
mghall999
mghall@...
Sep 23, 2009 11:27 pm
162
Merle, Alas, this is the case. #420 is considered a commercial product and is only available in boxes of 16. The best alternative is is a product called "duct...
Richard, ... Panasonic WM-61A connected to the Wallin Preamp. ... Sigh. I tried for years to do measurements on the cheap. Never had decent results. I used...
Richard, I forgot to answer one of your questions. Yes, you can eliminate the BSC filter if you use DSP to do the contouring. Another reason to use Foobar2000...
Hi Bob, Im looking for a nice sounding Monitor speaker. What do you have for sale for demo or assembled speakers and at what price? Do u have something which ...
CPal114@...
Oct 22, 2009 5:53 pm
167
Carl, I have two nice monitors, the FB-16 and the FB-20. See the Products page at my web site : Brines Acoustics <http://www.geocities.com/rbrines1/> I will...
I was shocked and surprised to find that Yahoo! closed the Geocities site that has hosted my web site for the last 10 years. Oh, well. The new web site is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
