Hallo, I'd like to make some calculations with the Deutschmann's Rh surface mechanism (either the Deutschmann et al., 2001 or the Schwiedernoch et al., 2003)...
Daniela, Ck2cti works only for Chemkin II files in gas phase. It does not support surface mechanisms as in Chemkin 3 and higher. You will need to do it...
Hello, I am wondering if sticking coefficients are implemented and evaluated differently in Cantera than that in Chemkin. I am getting different results using...
Hi all, I have run into a problem during installation of cantera-1.7.0 on a linux box (intel, RH WS4, gf/gcc). The problem appears to stem from the following...
Achilles Vassilicos
avassilicos@...
Jan 5, 2007 9:55 pm
1460
i am not able to convert any rxn mech files to ctml format when i try running ck3ctml.m i get a error message " wrong number of inputs " is there any any one...
Hi, I just installed cantera-1.7.0 an my Mac (Intel-based, 10.4.8) and it works nearly perfect ;) but it seems that the automatic conversion from cti-files to...
Hi Chitral I had the same problem: even in the calculation of the initial coverages I obtained different numbers, and this eventually led to a significant...
Hi- I am new to programming with C++ and anything object oriented. I have had success replacing most Chemkin subroutines with Cantera functions. However, I...
Hallo Chitral, I also obtained different initial coverages with Chemkin and Cantera, and that led to a significantly different output composition, if put in a...
Hi there, I'm using Cantera 1.7.0 on a Windows XP (32bit) machine (Pentium D). I've compiled the code on this machine using NET2003 and MATLAB 2006b. All of...
... MATLAB has a number of limitations as a front end for Cantera, or any C++ code. The biggest problem is that it does not provide a good way to manage...
Thank you for the quick reply, Mr. Goodwin!! Well, I have to admit that "big" is a very relative statement. It's not "big" enough that I want to switch to C++...
Dear Cantera users I am doing some calculations using the Leeds sulfur mechanism extension (cantera 1.6 through python 2.4 on Red Hat Enterprise Linux WS 4)...
Yes, you may be able to do it. Cantera does not catch every possible error that can be made... But I would strongly advise reviewing the high temperature...
Hi David Thank you very much for your advice. I agree that kinetics calculated outside the valid range of the NASA polynomial coefficients is likely to be...
Hi, I've been trying to implement a piston moving in a cylinder in cantera using matlab but havent had any success yet. I was able to get the same working in...
I have been using reaction data from h2o2.cti - whose mechanism is this and when was it validated? If anyone has information, please let me know. -Shannon...
Are you solving an internal combustion engine case? The following part is to calculate correct piston speed, cylinder volume, and rate of volume change using...
Hi, Yes, i am solving for an internal combustion engine case. I got the code which was posted by Dr.Goodwin earlier on to calculate piston speed, volume change...
Hello All: Has anyone else seen this? I am working with a colleague using Cantera to replace Chemkin in an application (Fortran and C++). We are using Python...
I found the documentation on SourceForge which said that if you want to use python to run cantera, just run the binary installer. So I: 1. Installed Python 2.5...
I'm trying to find the documentation - particularly how to install libnumeric for winxp using python scripting. But the link to the documentation on the...
I've run into a problem while looking at the "combustor.py" example for python (steady flow combustor problem with two mass flow controllers...etc.). If I run...
Hi Cantera Users, has anybody tried to model steam methane reforming over a Nickel catalyst including surface reactions? Any code available? Any help will be...
Yes, we do this using the recent mechanism developed by Prof. Olaf Deutschmann's group at U. Karlsruhe. I can send you their reaction mechanism converted into...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
