Dear All - I'm pleased to announce the introduction of ChiefSymbols® Library CC17. To determine the contents of the new library we tallied the search results...
On Tue, 1 Mar 2005 15:16:41 +1100, "Paul Hilbig" ... I hear that! The current library browser sucks. The aerial view could be handy but it is too small and...
Hi All Have reached the stage where the old Epson wastes loads of paper and is going to get the flick very shortly. The Canon i9950 which sounds promising from...
On Mon, 28 Feb 2005 22:01:31 -0800, "Robert" ... Uh, no, you don't. It absolutely "is" possible to break the library window out of the main window and drag it...
On Tue, 01 Mar 2005 05:02:19 -0000, "Lewis Buttery" <lbuttery@...> ... I think you also have to "yank" it to the second monitor so it doesn't grab onto...
Steve, I did a search on Pricewatch.com some time ago for that printer and also read the comments from people who had purchased and used it. The only negative...
Build>Framing>Bearing Line/Joist Direction Tell Chief which interior walls & beams are load-bearing with the Build > Framing > Bearing-Line tool. With it, draw...
Has anyone set up a layer set to match the AIA layers? I was thinking of setting up my V10 with that set. If so, would someone upload that for the rest of us?...
Still looking to see if there are any Chief Users in my area that would be interested in full time employment or to do drawing for me. We are a high end...
I went to Preferences, Appearances. the very top one on the left; Contextual Menu. You can stop them or fix it so that it drops down with a dbl. click. Hope...
Can anyone tell me how square footage is measured in a home? Is it the outside perimeter of the entire house or is it only the living space areas added...
... manuals ... sell it. ... from ... if a ... = The key factor here is getting the licence tranferred, so that you are able to upgrade. As good as SB is for...
I found the "Square Footage - Method for Calculating: ANSI 7Z65-2003". It's $20 for a hard copy or $10 for a PDF. It sounds like it is exactly what I'm...
Terry, Depends who you ask!! Architects calculate sq ft from the outside edge of exterior walls for buildings. Landlords for tenant spaces calculate from the...
if you have already built the roofs, the setting in the BUILD ROOF dbx will not remove the boxed eaves...you need to open the roof plane(s) dbx individually or...
a couple of points.. holding down the Ctrl key OVERRIDES the docking of the library...BUT only if it is already undocked...this keeps it from trying to dock...
I have the HP Designjet 120 for sale. It was only used for five sets of
prints. The ink tank indicators have not moved from the full position. I
am going to...
Eugene, I am ignorant of current plotters. How long has this unit been out? And is it a sheet feed or roll feed? Thanks, Chris Murray ... From: Eugene...
I started using V10 and whenever I print a floor plan in is in the center of the paper and very small. I have a HP Deskjet 1220c. I have tried to fax the floor...
Hola all, When framing a roof I noticed there is no framing for boxed eves, should there be and if so how? It frames roof returns. Thank you, Barry Mexico...
If you already have it why not install ? I would use it as a learning tool for now and not do any "critical" plans in it. I will keep using 9.54 until I see...
Hello Everyone, There seems to be some confusion about the V10 library browser so I thought it would be appropriate to try and clear up some of these issues. ...
Does anyone out there think we should have a point to point copy tool? This would save a step in my opinion. It would be nice to have a transform/replicate...
The builder has sent a DWG (AC2000) that has all text for construction notes for Maryland. What is the process for importing these notes into a plan and then...
I am using the Canon i9900 which I presume is similar to the i9950. My experience for my low volume use requirements has been very positive. It is very fast...
