Thank you, Glenn and Timon. The line label thing is in the same place as before. I only use it for my site plans and it turns out I had set that for a higher...
Ellis, I've also had to reduce text/dimension size by about 25%. Jim James A. Lawes East Bay Design 231.322.8702 www.eastbaydesign.net Ellis, I've had to...
Where is the default hatching pattern for walls defined? I'm referring to the 'hatch wall' tool, not the 'wall definition dbx'. Jim James A. Lawes East Bay...
When I insert a CAD Block to page 4 of my layout, if I explode the block then all the text moves to page 0, then I have to go to page 0, select all that text...
Jim, The only way I know is with the hatch wall tool active, you can change individual walls or multiple select. Double click the hatched wall and you will...
Hi Bill, If you place a CAD block directly in the layout, then explode the block, all the entities contained in that block will revert to the corresponding CAD...
Thanks Bill, But I'm still not sure if it is me misbehaving or Chief misbehaving? I mean, how would I know what page I'm going to end up using a particular...
Hi Bill, I guess what I am wondering is why you would want to edit a CAD block in layout. If it were me, I would place it in a CAD detail and work on it ...
Bill S, The reason I was exploding the CAD block on the layout page is because this particular detail is a wall section showing the footing below ground, and...
HI, Does anyone know if there is a way to offset either the newels or baulisters for a stair railing? I know that the settings are in the default preference...
If I send an elevation view to cad and modify that view, is there a way to get it back into chief as a symbol with the modification still in tact? I know...
Steve I can't help you because it's happening to me too after doing a quick test. I hardly ever use cabinet labels so haven't noticed this problem before. It...
On Fri, 1 Apr 2005 18:33:16 -0600, "Lamar Hunter" <lhunter@...> ... Hmmm, not sure but my instincts tell me that you can save it as a CAD block but not...
Paul, Thanx for the response. I do alot of kitchen additions.... I hope ART will fix this someday :) Regards, Steve In a message dated 4/1/2005 9:21:23 PM...
I'm interested in making a 3-way switch between floors. I want a switch at my front door entrance that will turn on lights in the living area, but will also...
Charlie, Use the S3 from the electrical library and a cad arc with the same line style as your electrical connections on each floor. In other words "fake it"...
On Sat, 02 Apr 2005 10:32:17 -0500, Charles Cavanaugh ... Much like John says above, I use an S3 switch and substitute a curved dashed line for the electrical...
I use cad arc and plines set to electrical connections line type for all my wiring. I find it much faster and more accurate in positioning arcs. ... "fake ... ...
10.3 upgrade available. Go to chieftalk, announcements to find the link. This patch claims to fix the layer protocol to a logical system. I will be trying it. ...
Thanks for the heads up Mark. 8^) Bill Shideler Homes By Design http://www.HomesByDesign.ws Vancouver, Washington 360.254.0972 ... From: "wlsquared0ver8"...
Maybe I'm reading the question wrong but I put an S3 down in the basement and then drew a connection to another S3 at the top of the stairs using Chief's...
Am I alone in the program crashing alot? V-9.54 was running without hardly any crashes and V-10 updated to the latest patch is crashing about 6 times a day....
Any one have any good thoughts on a good program for cal floor jst, ceiling jst and roof rafters? I was looking at beam chek - thoughts? Larry [Non-text...
73592
Walter Fuller
walter@...
Apr 3, 2005 12:43 am
Larry: I've used BeamChek for several years now and find it to be an effective tool it works for dimensional lumber, engineered lumber (Microllams and ...
I am using chief architect 8 and my operating system crashed (windows xp pro) i have saved all the data on the old hard drive and reinstalled a new drive...
