... yes I believe so. I have used some software from National Semiconductor call "Plan" to generate JEDEC files and have subsequently used the files in other...
David Timmins
dtimmins@...
May 1, 1998 8:36 am
52
Hi all I want to have a composite video output from a svga monitor or convert an RGB,H sync ,V sync to a composite video signal How can i do this Mohamed...
Mohamed Shoura
m_shoura@...
May 1, 1998 1:36 pm
53
Hi Roland ! When you have 15 degree step motors, you can get 7,5 degree steps if you modify the control sequence of the motor coils A resp. B. 15 degree: A /...
Bertram Geiger
bgeiger@...
May 1, 1998 2:29 pm
54
... This was stupid of me - I've got a typo there. Let us decide (for terminology's sake), that the TSR 002 is a FET. The VDS should be 1.5 VOLTS, NOT 4.5...
Declan Moriarty
genius@...
May 1, 1998 5:13 pm
55
... Dear Gary, I have to ask - Have you changed the boot disk? Have you a compatible Dos Version? You could have trouble with anything before DOS 5. I got...
Declan Moriarty
genius@...
May 1, 1998 5:15 pm
56
Can anyone point me to data on Analog Devices # AD1848? Neither their web site nor current literature show this number although AD1847 and AD1489 appear. This...
Mike Turner
MikeTurner@...
May 1, 1998 6:30 pm
57
... The Boot disk is 6.22 thats works on another machine. I think it is the motherboard which will be recyled back to its original state. Sounds like fun....
Gary Regez
glregez@...
May 1, 1998 9:19 pm
58
Lisbon, May 2nd, 1998 Hi there, I do not know if this subject is a little off-topic but I need some help... I need to know how can I reprogram the CMOS memory...
António José Go...
ajose@...
May 3, 1998 12:09 am
59
Yet another mouse question... What is the protocol of these new serial mice with the additional knob which can be used for scrolling? What about the IBM mouse...
Mario Becroft
mb@...
May 3, 1998 1:30 am
60
... You should recieve a file called "40SXDIAG.ZIP" to make a setup disk, I sent it to your E-mail address. I hope this works for you, ...............Bm -- ...
Byron L. Miller
byron13@...
May 3, 1998 1:59 am
61
... Strange, I have a lot of data about the chip... For a new design use the Crystal chip (CS4231A) however, it's upward compatible but much better. It's on...
Jaap van Ganswijk
ganswijk@...
May 3, 1998 5:14 am
62
... You can find these things in the 'Chip Directory' (see in my signature). http://www.mitsubishichips.com - Chips ...
Jaap van Ganswijk
ganswijk@...
May 3, 1998 5:29 am
63
Hi I'm looking for an rs-232 level converter similar to the MAX237, but that is smaller physically. It is for an modem aplication, so I need a chip with 5 ...
Nic van der Walt
nvdw@...
May 3, 1998 12:29 pm
64
Do you want to do this as a one-off, or massproduce a product? If the former, you can buy a box that does the job for a couple of hundred dollars. If you want...
Peter Vogel
pvogel@...
May 3, 1998 1:03 pm
65
Hi Please Peter tell me both of them :The Chip and the Box But can i use this to convert a non-standard video-signal to a PAL one Mohamed Shoura ... -- Author:...
Mohamed Shoura
m_shoura@...
May 3, 1998 2:18 pm
66
Hi All, Please cuold any one let me know where i can get data sheets of the following IC's: MC145191 HC74 HC04 Harris Regards mchd mucefi -- Author: INET:...
hosein31@...
May 3, 1998 6:35 pm
67
I must write a relation for an electronic course. I have a question! What is the difference betweein RS-232 and (RS-422 ,RS-485) interface Thank in advance -- ...
hi the mitsubishi web its not very good, but if you send a email to support, they are excellent, you can find the email adresses in the web.... I dont know...
Jose Luis Hidalgo
jhidalgo@...
May 3, 1998 9:29 pm
72
CHIPDIR-L@...
May 3, 1998 10:14 pm
74
CHIPDIR-L@...
May 3, 1998 10:23 pm
75
CHIPDIR-L@...
May 3, 1998 10:33 pm
76
Try MAX233 or MAX203 Neither one of these require CAPs to operate. ... is ... 5 ... -- Author: INET: rebeltech@... Fat City Network Services...
Rebel Tech (Jeremy N....
rebeltech@...
May 3, 1998 10:49 pm
77
Hmm, Interesting, You can't reload dos without a boot disk, although windows, I have personally done with out a floppy in the machine, but it's not for the ...
I need to design a serial link that will transfer data at 10mbits/sec over say 100m. RS-422 for example, but I can't find any specs for line length vs speed. ...
Peter Vogel
pvogel@...
May 4, 1998 1:48 am
80
Where can I buy the box you said? What company it is made by? Thanks in advance. ... From: Peter Vogel [SMTP:pvogel@...] Sent: Sunday, May 03, 1998 9:46 PM...
wang@...
May 4, 1998 2:33 am
81
Hmm, Well Peter, you might try designing the circuit after Ethernet Standards. If you use ethernet line drivers, you already can pull up specs on the line ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
