Does any one have a datasheet, or at least a pinout for the HD49733 chip? Hitachi VCR IC: semi-custom servo chip? 56-pin shrink-DIP (.07" between pins) and .6"...
Brad O'Dell
brodellml@...
Oct 2, 2003 8:44 am
5504
... Thst's why I said TAP it with a hammer. I didn't say smash it. I've opened a number of potted assemblies that way but it's up to you how you want to do it....
Joe
rigdonj@...
Oct 2, 2003 3:25 pm
5505
Hi Joanne, ... Since you talk about 'your OEM', I assume you are a chip broker. Instead of asking for chips here, you'd better subscribe to one of the services...
Jaap van Ganswijk
ganswijk@...
Oct 3, 2003 5:59 pm
5506
I have recently had my old pc blown away for myself, which prompted me to upgrade it. All good so far. Linux I could sort out without hassle. I've lost the...
Declan Moriarty
tech.genius@...
Oct 6, 2003 6:37 pm
5507
Hi Declan, ... This lookes like a winsock.dll which is not apropriate for your windoz version. I am not a crack in this stuff, but search in that direction....
H.C. Croon
h.c.croon@...
Oct 6, 2003 10:05 pm
5508
On Mon, Oct 06, 2003 at 02:59:29PM -0800, H.C. Croon enlightened us thusly ... Thanks, Harry. Microsoft are not my enemy - I just avoid as far as possible,...
Declan Moriarty
tech.genius@...
Oct 7, 2003 8:59 am
5509
... Sorry Declan, It was a wrong estimation. From your mails I had the impression that they are not your friends, (mine neither). Best regards, Harry -- ...
H.C. Croon
h.c.croon@...
Oct 7, 2003 12:10 pm
5510
On Tue, Oct 07, 2003 at 05:04:19AM -0800, H.C. Croon enlightened us thusly ... Ok. The results are in. I removed modems(It multiplies them), the dial up...
Declan Moriarty
tech.genius@...
Oct 8, 2003 1:58 pm
5511
... This was the wrong place. I had similar problems. Try to open ControlPanel/network -> and remove at least tcp/ip there (or better remove all entries:-);...
Matthias Weingart
matthias@...
Oct 8, 2003 6:19 pm
5512
Hi, Also remove the Client for Microsoft networks (and File & Print Sharing) if you have then installed and reboot (or at very least, get of the networking...
James Afford
iissa@...
Oct 9, 2003 6:39 am
5513
Hi everybody, anybody out there would have a M/D Totco Drillwatch calibration software CalConf V4.36 ? I do have the original diskette, just it's damaged, and...
Friedel Bruening
bolinst@...
Oct 9, 2003 4:18 pm
5514
Brad, I have a schematic diagram from a vcr that use this IC, I can scan it and send by e-mail. Miguel...
Miguel Venditto
mvenditto@...
Oct 9, 2003 11:20 pm
5515
I'm trying to find out how the parental control feature on DVDs is encoded on the disk - is there an EIA standard or something I can refer to? I know that...
Peter Vogel
peter@...
Oct 10, 2003 3:06 am
5516
Hi All, may be some one keep default pass code for onan generator set ( the genset panel using 16x2line display ) or have another way to crack it, i need it ...
Tamtam Bastaman
tamtam@...
Oct 10, 2003 7:00 am
5517
One errata: ATSC = Advanced Television SYSTEMS Committee. :D George ... Sent: Friday, October 10, 2003 10:02 AM To: 'CHIPDIR-L@...' Peter et al: I...
George Mena
George.Mena@...
Oct 10, 2003 5:15 pm
5518
Peter et al: I believe the EIA standard you want is EIA-744, if the USA's FCC is to be believed: ...
George Mena
George.Mena@...
Oct 10, 2003 5:16 pm
5519
Thanks for your note George. The information I was specifically looking for is the mechanism by which the parental control code is stored on a DVD; is there a...
Peter Vogel
peter@...
Oct 10, 2003 10:20 pm
5520
Peter et al, It's not elusive. It's in Part 3 of the DVD-ROM Specification, as put forth by the DVD Consortium. The DVD-ROM Specification is part of the DVD...
George Mena
George.Mena@...
Oct 10, 2003 11:24 pm
5521
Hi everybody, anybody can tell me something about an 90A810 or 90C810, made by ST, but no datasheet available so far I have seen. It's a 14 pin SMD, pin 4 has...
Friedel Bruening
bolinst@...
Oct 11, 2003 6:27 pm
5522
On Sat, Oct 11, 2003 at 11:19:19AM -0800, Friedel Bruening enlightened us thusly ... Some of these parts are tested for a closer tolerance, then batch ...
Declan Moriarty
tech.genius@...
Oct 12, 2003 10:06 am
5523
Yes I got it out of the box (inox) using kind heavy equipment for such delicate stuff, I attacked with aceton, that was completely useless and a waste of time,...
Friedel Bruening
bolinst@...
Oct 14, 2003 12:00 am
5524
Good luck Friedel. Fortune favors the driven. J -- Author: INET: HnrBnd@... Fat City Network Services -- 858-538-5051 http://www.fatcity.com San Diego,...
HnrBnd@...
Oct 14, 2003 1:24 am
5525
I wonder if this would work with IC dissection? Husky injection-molding machines make a tool to remove plastic from injection-molding machines, especially...
Jeffrey Meade
jeffreymeade@...
Oct 14, 2003 3:01 am
5526
Fascinating treatise, Jeffrey; But if the money for that sort of kit was in his country, he'd have told the owner exactly where to go with this thing ;-) On...
Declan Moriarty
tech.genius@...
Oct 14, 2003 9:25 am
5527
On Wed, Oct 08, 2003 at 11:34:19PM -0800, James Afford enlightened us thusly ... Sorry lads. I did all of the above, and it all failed. Norton bellyaches that...
Declan Moriarty
tech.genius@...
Oct 14, 2003 5:28 pm
5528
Hello, Im desperately seeking a dozen or so of the obsolete M3002 real time clock from EM MICROELECTRONIC MARIN SA Tel. +41 32 755 55 30...
Darren Logan
Darrenl@...
Oct 15, 2003 8:00 am
5529
Hi folks, anybody can point me to the datasheets for : M52765FP AN8962SA found in a Panasonic TV-set Tuner which turns of the color after some 15 minutes of ...
Friedel Bruening
bolinst@...
Oct 16, 2003 1:35 am
5530
I found availability for M3002-16PI from two sources: Manoshevitz Electronics in Israel has 1 in stock. 4Source Electronics AG in Germany (www.4source.de) has...
TQuiroz@...
Oct 16, 2003 6:14 am
5531
A few suggestions: Try feeding a video source through the video inputs. This bypasses the tuner/IF section. If the problem is still there, then the tuner is...
TQuiroz@...
Oct 16, 2003 6:26 am
5532
On Wed, Oct 15, 2003 at 06:24:20PM -0800, Friedel Bruening enlightened us thusly ... I will look for them (I have a load of TV parts here). I don't want to ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
