Hello friends I want to configure Cisco router 2800 with NM-1CE1T1-PRI module for dialup access from analog telephone line. We have PRI with 10 channel. I have...
Noufal Abdurahiman
noufal@...
Apr 17, 2007 8:48 am
12654
Noufal, Your debugs show that the router is answering the call, but the circuit network is clearing the call about 2.5 seconds later: *Apr 17 07:36:32.235:...
Aaron Leonard
Aaron@...
Apr 17, 2007 4:09 pm
12655
We have Cisco 7507 and we its already connected to Radius server. We have pppoe and pptp clients We want to configure the cisco to limit the users based on the...
Abdullateef Barakat
latif@...
Apr 22, 2007 1:05 pm
12656
Hi, Im trying to configure ISDN BRI call-out, and seems like I have run into some problems. When trying' to call anywhere, and with 'debug isdn events' I'm...
Andris Zarins
a.zarins@...
Apr 26, 2007 1:18 pm
12657
I am trying to setup something described at http://www.cisco.com/en/US/customer/tech/tk801/tk379/technologies_configuration_example09186a00800949ee.shtml To...
Gaurav Sabharwal
gaurav@...
May 2, 2007 8:27 am
12658
... http://www.cisco.com/en/US/customer/tech/tk801/tk379/technologies_config uration_example09186a00800949ee.shtml ... Do you *only* want to the ISDN caller-id...
Oliver Boehmer (oboeh...
oboehmer@...
May 2, 2007 2:23 pm
12659
Gaurav Sabharwal <mailto:gaurav@...> wrote on Wednesday, May 02, ... http://www.cisco.com/en/US/customer/tech/tk801/tk379/technologies_config ... Ok....
Oliver Boehmer (oboeh...
oboehmer@...
May 2, 2007 6:15 pm
12660
on 05/02/2007 08:11 PM Oliver Boehmer (oboehmer) said the following: {snip} ... We are implementing this service for a customer that manage the CPE using a...
Gaurav Sabharwal
gaurav@...
May 2, 2007 6:39 pm
12661
If you have only one mad customer you dont need a huntgroup. Make a default entry: DEFAULT Calling-Station-Id == hisnumber, Auth-Type:= Accept ...
tnt@...
May 2, 2007 8:26 pm
12662
... The goal is to use only the ISDN CLID for authentication. The remote router will not be configured with any username/password information. ... The document...
Gaurav Sabharwal
gaurav@...
May 2, 2007 8:29 pm
12663
Gaurav Sabharwal <mailto:gaurav@...> wrote on Wednesday, May 02, ... And the code/GUI really deploys a dialer without any ppp authentication? This is...
Oliver Boehmer (oboeh...
oboehmer@...
May 2, 2007 10:38 pm
12664
... Unusual would be the right clinical term :-) But hey, Customer is always right. ... We already have 2811 and would prefer to use them. I will have to get ...
Gaurav Sabharwal
gaurav@...
May 3, 2007 1:42 am
12665
Gaurav Sabharwal <mailto:gaurav@...> wrote on Thursday, May 03, ... sites ... Yes, the same username/password on all sites and CLID check on the Radius...
Oliver Boehmer (oboeh...
oboehmer@...
May 3, 2007 5:11 am
12666
Hi All, Another question from a newbie and forgive me if this has been answered previously. I have an issue and I am not sure if this feature will work with...
Eugene Patton
Eugene.Patton@...
Jul 20, 2007 12:12 am
12667
... (VPN) but ... no, "ip:inacl=<acl-definition>" is not processed by IPSec (as "debug aaa per-user" would likely confirm), and the way you've described it is...
Oliver Boehmer (oboeh...
oboehmer@...
Jul 20, 2007 6:12 am
12668
Hi Eugene, Try to use wildcard ACL on radius if You are using normal ACL (or opposite.) Best regards, Ladislav. ... From: cisco-nas-bounces@... ...
Nemec Ladislav
Ladislav.Nemec@...
Jul 26, 2007 10:16 am
12669
Hi There... I work for a service proivder and I'm trying to load balance four of our radius servers using IOS SLB. The config works well and the radius servers...
Andy Saykao
andy.saykao@...
Sep 13, 2007 2:46 am
12670
Just wondering if anyone has implemented radius load balancing before. This is our current setup (note: I am trying to implement radius load balance in the ISP...
Andy Saykao
andy.saykao@...
Sep 19, 2007 5:36 am
12671
Hi all, I am working on one AS5350 to covert the codec and voice protocol, now I am using 2 T1 interface to do it. The call comes to the gateway and goes to...
David Lin
david.lin@...
Sep 27, 2007 3:44 pm
12672
David, Yes this is possible. This is called Cisco Unified Border Element (previously IP-IP Gateway functionality). This is supported on the AS5350XM and...
Darryl Sladden (dslad...
dsladden@...
Sep 27, 2007 5:26 pm
12673
Hi Darryl, Thank you for your assistance. My chassis information is as following, is it ok for this feature? Thanks. Cisco IOS Software, 5350 Software...
David Lin
david.lin@...
Sep 27, 2007 8:11 pm
12674
Hi all, Is it possible to set access control list for the voip inbound call dial-peer so that we can allow the particular IP address to match the dial-peer? ...
David Lin
david.lin@...
Oct 1, 2007 3:25 am
12675
Hi all, I have a AS5350, the NVRAM can't save the configuration whatever I set the config-register as 0x2102 or 0x2142. Once I restart the box, the...
David Lin
david.lin@...
Oct 4, 2007 9:16 pm
12676
My guess: bad flash. Aaron ... _______________________________________________ cisco-nas mailing list cisco-nas@... ...
Aaron Leonard
Aaron@...
Oct 4, 2007 9:19 pm
12677
The flash looks good, I can load any file into the flash and never lost. Only nvram, I always got 0x101 after reboot. Is it battery problem?> Date: Thu, 4 Oct...
David Lin
david.lin@...
Oct 5, 2007 2:24 am
12678
From a case survey, this is almost surely an NVRAM hardware problem. I had said "flash" because I was mistakenly thinking that on the 5350, NVRAM is part of...
Aaron Leonard
Aaron@...
Oct 5, 2007 4:43 pm
12679
In some older Cisco devices, if the processor board (where the NVRAM is located) is placed in Anti-static bags, the NVRAM was erased and/or the battery power...
John Shults (jshults)
jshults@...
Oct 5, 2007 4:49 pm
12680
Thanks Aaron and John. It seems not worth to get it repair. TFTP should be ok. Thank you. ... _________________________________________________________________...
David Lin
david.lin@...
Oct 5, 2007 6:15 pm
12681
Hi Nas, I set up a Facebook profile with my pictures, videos and events and I want to add you as a friend so you can see it. First, you need to join Facebook!...
Rifaat Abdin Ismail
invite+o_f=z096@...
Oct 30, 2007 5:07 am
12682
hi all, could somebody please point me to some sort of documentation as to why incoming vpdn sessions onto a NPE-G1 would sometimes end up in the wt-sss state....
