Dear all I'm a beginner with Comis and I have several doubts: - Comis use the correction factor (CF - from Dascalaki et al) only for single-side, is that...
Hi Manuel * The crack flow correction factor is implemented in COMIS subroutine CRTEMPC, in file COMV-CRA.FOR. It is as described in in AIVC Technical Note 29,...
Hi Raja, Your university is responsible for making the necessary user manuals available to you. There is a different manual for each library. The manuals for...
Hi Raja, Actually TRNSYS 16 now has electronic manuals. So, if you have that version, you can access the entire set through the Simulation Studio help menu. If...
Does anyone have a copy of, or a url link to, the User's Manual for CPCALC+? I'm trying to do an exercise of comparing several different ways to make natural...
as an alternative for your Cp calculations you may use the TNO 'Cp Generator' program. The web version of this program is now available for free to beta...
I hope someone answered before, but just in case: CPCALC+ can be found in the Files section of the Web site : http://groups.yahoo.com/group/comis/files/ ... ...
Deepak, ... COMIS, like other multizone models, predicts the airflows between zones (a zone is typically a room, or a group of rooms all tightly coupled by a...
David M. Lorenzetti
DMLorenzetti@...
May 16, 2005 4:33 pm
407
Deepak and members of the COMIS Yahoogroups, My colleague Zhengen Ren and I have modified COMIS to include sub-zonal divisions, treatment of flow drivers...
John Stewart
j.r.stewart@...
May 17, 2005 7:36 am
408
The explanations in both the COMIS and Energy+ users' manuals get a little sketchy from time to time. I'd like to be sure I understand how to enter upwind...
Well, it may be that my concerns are irrelevant. Doing some checking I found Message 179 that says that this portion of the COMIS code was not even implemented...
I'm an user of IISibat3. I find a problem when I use this program. When I establish a more difficult IISiBat document (the document is about more than 500KB),...
The routines for Cp calculation are neither in COMIS 3.0 nor in 3.1 implemented. In 3.1 the corresponding data entries have been canceled from the input file....
and of course you can use TNO's free web service 'Cp Generator' as an alterantive to calculate Cp values. http://cpgen.bouw.tno.nl Regards, Bas Knoll B. (Bas)...
I received the following information from the managers of Energy+: "There are no plans to migrate to COMIS Version 3.1, which is copyright by EMPA in...
While writing the TNO Cp-Generator program we considered implementation of the Cp-routines within COMIS. We are in the position to do so, because Hans Phaff is...
Dear Sirs, I've just joined your group and just started to use comis 3.0. I have a problem: I have to run both "ventilation" and "pollutant", but the output's...
Dear Mara If you have no other driving forces such as wind pressure, temperature differences or fans, then the density differences caused by different...
I'm an user of IISibat3. I find a problem when I use this program. When I establish a more difficult IISiBat document (the document is about more than 500KB),...
Dear weaker_shen, I think this problem should concern IISiBat/TRNSYS, not IISiBat/COMIS. (IISiBat 3 for COMIS does not exist). You should contact your TRNSYS...
Dear COMIS users, After a long period of waiting, I am happy to be able to announce that a new version of COMIS, COMIS 3.2, is now well under way. The latest...
Hi I was wondering if i could pose a question to you about COMIS? Regards Maggs Mahmood Mohamed Hoosain Information Technology Department Koeberg Nuclear Power...
Yes, you can. Werner ... De : comis@yahoogroups.com [mailto:comis@yahoogroups.com] De la part de Mahmood Mohamed Hoosain Envoyé : lundi 13 juin 2005 09:13 ...
The COMIS 3.0 manual gives you the distict impression that it calculates a Cp value specific to a location (x,y,z) on a face (pg. 101 "These routines calculate...
The manual of COMIS 3.0 contained several errors of this type (description of functionalities which were actually not implemented). The update of the manuals...
Hi Everyone I have question about the application of FRP duct. Can we use the FRP duct for kitchen exhuast duct? It's acceptable for NFPA96 or SMACNA? Thank...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
