Hello group Under &-WI, what is the value for Cs for open doors? Cs is defined as flow coefficient for close windows per m crack length. If the door or window...
... The Cs value (in the second row of the *W block) describes the window/door leakage when it is closed. As the window/door opens, the airflow is determined...
David M. Lorenzetti
DMLorenzetti@...
Oct 16, 2006 10:00 pm
622
Thank you, your response was of great help. I am modeling a type 1 WI so won't need to know how the opening fraction is used here. Thanks again for the quick...
Dear sir I have download the software of COMIS 3.0 with IISiBat from http://evl.cstb.fr/francais/projets/IISiBat/COMIS/confcom.htm. When I run the software, it...
As far as I know, this version does not run on Windows XP. I guess that might be the problem. Nicolas Heijmans Belgian Building Research Institute (CSTC - WTCB...
COMIS 3.1 does run on Windows XP, as well as its graphical interface. But you should not use the old (outdated link) to access it. The right link is ...
dear Werner and Nicolas Heijmans Thank you very much for your responds. I have download the COMIS 3.2 from http://software.cstb.fr/soft/present.asp?langue=us....
The older versions of COMIS also run on XP, as far as the kernel is concerned. The graphical User Interface, however, does not run on XP. You could try to use...
Hi there: I found this mistake message: the pollutant name co2 in schedule Qco2 matches none of the pollutants. Correct the input at &-NET-ZONE or &-POL-DES...
Dear all: I read about the content on histograms in the Comis user guide, but I wonder how I can difine the histograms in simulation studio? Thanks a lot!...
Dear all: I read about the content on histograms in the Comis user guide, but I wonder how I can difine the histograms in simulation studio? Thanks a lot!...
In the Studio, you define histograms in the 'Control Cards' (Control Card button or 'Assembly/Control Cards...' menu): Go to the Schedules/Layers/Occupants...
Dear COMIS group member I'm Fujikawa at Yoshino lab of Tohoku University Japan. I have a question about contaminant calculation. Sorry for my poor English. My...
Hello, Mitsutoshi, You can try our model COwZ (COMIS with sub-zones). There are no limits for the zone number. You can also get details of airflows,...
Dear COMIS users It is written on the user's guide that some couple of data(pressure and airflow rate) can be used as the performance of a fan. And it seems...
Hello, I don 't know TRNFLOW, but if its like in COMIS, fans are defined by a fan curve. There are two ways of doing this, either by giving data pairs or ...
... Typically in COMIS the pressure that drives flow through a link is the hydrostatic pressure difference. The exception is when the link connects to an...
David M. Lorenzetti
DMLorenzetti@...
Nov 17, 2006 5:18 pm
650
Hello, Does Comis adjust the Cp-values at an open window automatic? Or does it still use the values that are given as input? Thanks....
Dear all The different positions of a facade have the different Cp values, but in the &-CP-VALUes, it is only need to input one Cp value for a whole facade...
Dear Wangke, ... I usually get CPCALC (or the program that I prefer: CpGenerator) to calculate Cp values for various places on the facade to see the extent of ...
... The answer here is based on COMIS 3.0, the last public-domain version of the program. I imagine the current version of the code has the same basic design,...
David M. Lorenzetti
DMLorenzetti@...
Jan 11, 2007 10:27 pm
680
Hello, I see that COMIS has the capability to specify ducts that connect zones. However, are these ducts associated with an air handling unit that can...
Dear Lisa Yes, COMIS can model ductwork. There are a number of built-in ductwork components, such as bends and T-sections, for which COMIS calculates pressure...
Dear all: I have a problem on coupling TRNSYS16 & COMIS 3.2 with Type 157. Three notices and three error messages were found acoording to project log, as...
Read the readme.txt file in .\comis32\Binary\Trnsys16 of your COMIS 3.2 installation to see which dll you have to copy into your TRNSYS directories. ...
I will be out of the office until March 9th. Please excuse the delay in responding to your email. ... To: <comis@yahoogroups.com> From: "Andreas Weber"...
Dear Andreas Thank you for quick reply. After copying Type157.dll, I had another error message: Visual Fortran run-time error forrtl: severe (29) file not...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
