its pretty wuiet in here since a month. for normally this means jens is busy as hell ;) . i'm just impatient, so i need to ask: iirc, the original minimig core...
... I'm always busy, right :-) ... Last time I talked to Tobias, he was on a new version of the CPC core, so Minimig might not be his highest priority at the...
... It was a long way from the Minimig core to the C-One core. I is not possible to replace the old minimig source file with the new ones. Thats why I must go...
Hello, I have noticed that c-one.net is not available -> http://downforeveryoneorjustme.com/c-one.net which is bad... I know there is more documentation (as on...
Oops. I had to buy a new router (again) and forgot to set up the port forwarding. I'll get that as soon as I get home this evening. I have been hosting the...
... The extenders are shipped without the JTAG installed, but you can solder that to the board pretty easily. If you have a computer with a parallel port, I...
Hi list, Yes, you've read it right: The makers of the C-One have to reverse-engineer the C-One. I'm specifically talking about the configuration CPLD that...
Hi list, as promised yesterday, the updated schematics of the Instant-On board are online, and they now contain a basic description of what the config CPLD is...
Hi list, Peter has just uploaded a new version of his C-One core development manual, and I have also uploaded it to the C-One website www.c64upgra.de/c-one ...
Hoi group, I just uploaded a new Chameleon (preview) core. Just as Jens already mentioned there were a few problems with the joysticks. This has been...
Hi all, Excellent work. Just tried Peter`s new core and thought I`d pass on my findings. On start-up of Chameleon core, my CRT goes into HOR: 48Khz VER 73Hz...
Hi, ... Thanx ... Correct, that are the frequencies for the 800x600 mode that the chameleon core uses. Please try the 800x600_test_v3 core from my website. If...
Hi Peter, Thanks for that. My mitsubishi is a Diamond plus73 :) Tried your test_v3 core. Result is slightly different. Picture is more compressed, Thick, black...
Hi, ... I've searched a bit, but didn't get a clear Hz rating for this monitor (some sites state 66Hz but that is rather low), but it seems limited to lowish...
Thanks for your help Peter, Much appreciated :) I`ll start looking for a new monitor. Should be able to find one relatively cheap now at car-boot sales. Roger....
Hi Peter, I just made a very interesting discovery concerning monitor sync problems I had earlier. It seems I won`t need to hunt for a new monitor after all :)...
... The device might invert Sync signals. Some monitors take the sync polarity to pre-set the PLLs. Peter, would it be possible to cycle through the four...
... Thinking of it, this should be Ctrl-Scroll-lock, so it won't be pressed accidently. The Indivision AGA flickerfixer also has the possibility to invert sync...
... Yes it is possible, but I won't do that. There is already a register in $D0xx that allows control over the sync. So like I wrote before already: in the...
... This reminds me of something I forgot to report - Peter's v3 test core works much better on my monitor if I invert the vsync signal and rebuild the core....
Hi, Thanks for that, You too. Hope my info was of some use :) I will have a much better weekend now that my sync problem has gone. Roger ... [Non-text portions...
Before I start trying to reinvent the wheel... I figured I'd ask: Has anyone looked at porting the ZET - http://zet.aluzina.org/index.php/Zet_processor core...
Hi, ... Probably not, never heard of anybody that was working on it. ... Some info is available here http://syntiac.com/c_one.html The document you searching...
Thanks... found it. Very nice doc btw. Well... guess I better get started. :) see if I can get something ready for when my board arrives in the mail. -Blair...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
