I am a audio nut and I have several components that I want to be able to record and play. 8-Track Recorder 16-Track Recorder Cassette Player-Recorder Reel to...
I do believe what you are looking for is called a matrix switch. Think about 6 horizontal lines intersecting 6 vertical lines and you will get the idea. I...
... Thanks Jim -- it was .pdf comparing the Finco FM4G to a CM TV antenna - filename FincoFM-CMtv-tena.pdf After searching my disk (dont get old- i cant...
Howdy, If you still have the original info, please feel free to add it back in our files here and in the FM Antennas group. jim... ... any ... tena.pdf ... ...
I'm a UK national living in the US. I am getting together a modest, inexpensive record-playing setup with a mixture of European and US components. Major...
what interconnects did you choose? good luck with your project ... ____________________________________________________________________________________ ...
Hi dream7quest7. The interconnects I'm using are QED Silver Spirals. I've had them for years. I bought them cheap at an audio show a while ago. Whether they're...
I Just picked up this really nice 8 track / a.m. radio stereo unit. Cleaned up well and sounds great in one channel, but the other is much quieter and...
Some here might find this dual opamp interesting... http://www.national.com/pf/LM/LME49860.html Key Specification ... Power Supply Voltage Range ±2.5V to...
-Hi Larry, That input offset of 0.1mv, if to be believed, is far better than the previous miracle IC you got samples of. There's sure a lot of zeros twixed...
Hey Ray, With 140 dB of open loop gain, I'd sure hope the THD at say 20 dB loop gain would have multiple zeros after that ubiquitous 'dot'. That alone should...
Hi folks, I know this has been covered before but I am in a tweaking/vibration damping mood. I have placed a rather heavy cutting board on the player and it...
Major enhancement to my Arcam Alpha 9 CD: 1. Artificial Pumice Feet ! Astonishing improvement in focus 2. Blacklight CD Mk2 + attached Black Hole CD stabiliser...
Check out GB Electrical Model # DS-110 duct seal. It's a heavy gray putty for sealing electrical connections and wires in metal duct work. $2.05 per pound...
Here is a very good read. In PDF form . Even if you agree, disagree or some where in between. Much information here. Including "damping" an external CD burner...
Thanks for sharing, Jim. But, it seems like if you're going to extract the CD contents to your hard drive using EAC (which eliminates all playback errors), I...
You are right Eli! One step forward and two steps back. For those that read the PDF and considering the cost of a dedicated laptop, external burner and high...
I have a new project, I'm going to go active on my front speakers(this system dose both 2ch for music and suround for movies). My plan it to do the LCR...
Hello Richard, I'll be so bold as to weigh in a bit on active crossovers. My present, 2-channel, system is quad-amped. 0 to 75HZ, 75 to 500HZ, 500 to 3500HZ ...
I happen to fave a bunch of Carol I guess cat5 cable. say's 18awg on it. Got 3 insulated wires and one naked silver colored twisted wire. The insulated wires...
That is not CAT5 as I understand CAT5. CAT5 is 4 twisted pairs of solid 24 AWG. The wire that you have could still be used for speaker interconnects. I would...
New Home Page photo shows one of my friend Ken's Rec-O-Kut creations happily playing at my place. Layered plinth of two MDF and two birch ply. A Rega RB250...
I asked my pal Ken Valliant to try and build a DIY 12 inch tonearm. Results of his latest valiant effort are on the Home Page. I'll add a photo folder too. A...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
