This is a FAQ for the DIY magnet use group at....http://groups.yahoo.com/group/diy_magnet_use/ It will be modified over time as new ideas and info become ...
diy_magnet_use@yahoog...
Oct 1, 2005 10:37 am
119
This is a list of factors expected to affect how fuel line magnets can be used. This info will change over time..... 1) what affects the fuel in the line is...
diy_magnet_use@yahoog...
Oct 1, 2005 10:37 am
120
Does somebody know where to buy a chip gaussmeter that can measure upto 20000 gausemeter and no spend more than $100...
Hi Guys, I want to do some experiment with magnets but have some questions: if I have a bar magnet and pass it throught a coil we know that it will will...
... Check here... http://www.kjmagnetics.com/specs.asp You can get either an N32EH or a N28Z magnet with a Guass rating of 11.1-11.9KGs and 10.4-10.8KGs...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the diy_magnet_use group. File :...
diy_magnet_use@yahoog...
Oct 2, 2005 2:08 am
124
From what I understand about neos (just learning for sure)...depending on how the magnet "set" is designed (that is how the magnet is used with steel, other...
As far as I know...they are "permanent magnets"...so they shouldn't lose strength to any degree. It does take "energy" to move the magnet or wire coil...
See within... Hope this helps, Robert ... ***For more information, see my other post called "Neodymium Magnet Information" ... ***This particular magnet from...
Neodymium Magnet Information This information was taken from here... http://www.kjmagnetics.com/neomaginfo.asp Demagnetization Rare Earth magnets have a high...
Good...detailed info. I like it. I've bought 2 sets of (4) 2x1x1/2 neo 40 magnets....1st 4 are Ni plated...2nd 4 are Ni-Cu-Ni plated...from China...and are...
Flushed the AT today and found NO steel particles collected where the single with backplate ceramics were located. Using my trusty DIY flux meter (small...
At one time I measured the temperature under the hood with the car I'm testing at the following: ambient temp: 79 F cruise with AC on: 125F to 132F run and...
Saw some guy with a 190D used HDD magnets, they're damn powerful, I must say. I've only got two now though, is this enough, or should I get some more? For the...
You could use the "total flux exposure" method to try and figure out how much flux you are putting to the fuel line. You'd have to measure the magnets for...
Ran another test measuring the air temps near where the magnets are installed on a day where outside temps were in the 81 F to 85 F range.... temps found under...
... Yeah, that is the one. These two magnets were good enough to smash the hell out of my finger, so I'll have to figure out what they are made of. ...
When you mess with the bigger neos it's best to have only one on a table at a time...otherwise stuff starts to happen when you don't expect it....and you can...
In a hurry and couldn't figure out how to upload a link, so here it is. http://www.scitoys.com/scitoys/scitoys/magnets/magnets.html Happy Testing, Robert -- ...
Did you ever get those magnets on the line? I'm guessing that they attract? Meaning N-S poles opposite? The N-S pole opposite is something I want to...
These are some ideas (gleaned from patents and websites) on various ways to set up magnets on fuel lines. I will change this over time and repost it as new...
There are LINKS to a free student version (36 MB) and a "Basic User Manual" on this page that should allow most people to to configure this program to show the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
