Hi I am going to thread mill some tapered pipe threads . They are 1.5"-11.5 LH USA pipe. The taper is 0.062"/foot. What angle do I set the taper on in the set...
Michael, I was just on you web page. I went through the movie on level 2. All went well until it got to the engraving Just before entering the engraving part,...
I'm a licencsed Partmaster user and have recently gone from a Windows/Mach2 controller setup to a Linux/EMC2 setup. I'm wondering if its possible to run...
Hello Jim, I haven't heard of anyone trying this so I can't say yeah or neah. Even if it runs it is very unlikely/almost certain that the software protection...
Yes Andre - that was actually my big concern - and I'm a little afraid of burning my software key in the attempt... :-) Once I pull it off of my current...
Hi Bengt - cost basically. I started down the hobby CAD/CAM/CNC path a few years back, and shortly thereafter had to put it on hold for a while. At the time, I...
Hello Jim, I will ask John P to have a quick think about this. ATB Andre ... From: Jim Stoll To: dolphincadcam@yahoogroups.com Sent: Tuesday, October 31, 2006...
Jim We would be happy to give you a Limited dongle i.e. 14 days, this would provide The opportunity of proving if the licence token Can reside on a Wine...
Jim The normal licence token system may not Work under Wine but the usb/parallel dongles could Be a different matter. I will ask the question of our supplier. ...
Heh, heh... Wish I could tell you more about Wine, but I'm a relative neophyte myself - I'm just trying it out for the first time this week. Give me a few days...
In order to transfer the software key to a.n.other PC it is first necessary to * Install the PartMaster software on to the target machine. * From the Help menu...
... Now *that's* funny! (and good advice, too!! :-) Thanks for the clarification and advice - I'll follow that path, and if it gets to the point where its...
Has anyone modified a PPR file specifically for EMC2, or is there one that is known to be directly compatible with EMC2? I'm currently using the stock...
Hello Jim, Have a look in the post processor folder on the user group site. There is a post for Turbo CNC which may be better than using the MACH post. If not...
Using 9.1.011 mill module... If I do a job with a slot and different Z feed, the post outputs that but if I do a job with holes, It won't put out the slower Z...
I have looked at the help file again and this is what it says: The Radius Offset and Length Offset fields refer to the offset registers of the NC machine, they...
I presume you're using mill? depends what machine you're using. If mill, all tools have a different length which is set against some reference point (usually...
Steve, It is Mach3 I am using on a milling machine I converted, What i was hoping it was for was for like you referd to tool wear so that I can adjust for...
Jim Some CNC controls use a Offset Register to store Tool radius and Tool Lengths (mainly mills). Where this is the case the radius is usually a 'D' address...
When you say holes do you mean drilling ? if not what command are you using ? Using the Select Tool dialogue gives you two feedrate options, the Principal ...
Jim, It's really each to their own, though personally & probably most people will define their tool(s) and let partmaster do the hard work and output the ...
Andre, yup drilling, yeah I figured that out, perhaps the select tool box could be made a bit more explicit... thanks anyway steve ... From: "Andre Mann"...
Steve, Thanks for that it has cleared up the query Jim ... From: Steve <steve_vagg@...> To: dolphincadcam@yahoogroups.com Sent: Saturday, November 18,...
setting go round in mill to no offset to machine along a line, lead in and out don't work. If I offset it left or right, it's quite happy to pay attention to...
... You can't have a lead in or out on no offset. No offset means follow the line. Think of a slot for a key, if it leads in it's not a straight line Lead in...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
