Hello Bob PartMaster Cam has post processors for the complete range of Prototrak controllers, LX2, LX3 for Turning, MX2, MX3, MX3E, A.G.E. for Milling. They...
Andre, you helped make my decision. Thanks much, Bob Wilgus ... Prototrak controllers, LX2, LX3 for Turning, MX2, MX3, MX3E, A.G.E. for Milling. ... flavours,...
... but ... intended ... It's probably a couple of months since I signed up, but no-one else has directly responded so I'll have a go. I'm currently running...
... Hi Andre, In my case I was using a std. 1" end mill to mill the floor of the slot flat to final depth but .0625" from the sides. I was following this up...
... Rather than implementing a separate calculator as a "tool" I'd prefer to see an "arbitrary expression evaluator" implemented within all numeric fields ...
... Thanks Steve, it's now on my shop wall :-) Cheers, Chuck Hackett Merry Christmas to all and may God bless you and yours in the coming year. "Good judgment...
Hiya guys, just wondering if anyone has a Mach2 post processor for the lathe module, which will output line numbers over 10000? I have emailed Michael about...
The offending line is in the "WORDS" section of the post ... This line in effect is saying "output block numbers with the letter N and allow upto 4 digits...
... I'm getting exactly the same (with different tutorials). I see you had no reply, but looking through the release notes file there's a reference to this...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the dolphincadcam group. File :...
dolphincadcam@yahoogr...
Jan 14, 2005 11:28 am
694
Hello Tim and rs274d I didn't see the original message about the corrupt font files, but there is obvioulsy a problem that needs to be sorted. I have informed...
Some users are experiencing problems with the "stick" font files. The error message is that the font file is corrupt, we are investigating this. In the...
The "Command" entry field does indeed support a fully fledged expression evaluator complete with sin, cos, tan and sqrt functions. e.g. to draw a line exactly...
Any chance someone could compile this new Mach2 post for me please? I am sitting here with a 13000 line number program in front of me full of asterisks which...
... Andre has put one in the files section, go to :- Files > Post Processor Files > Mach2 post files Out of interest how can you get a lathe ptogram that big? ...
Hi John, unfortunately my version of Partmaster does not allow me to compile the ppr files into a proper post file. Unless I am doing something wrong, then I...
HI all, help! I'm trying to talk to the PNC but it won't have it at all, I can talk to it via the original DOS software but not with PM comm package. Is...
... Hi Steve, I can remember struggling with the same problem with a PNC3-equipped Easimill in the early '90s. I ended up using Windows Terminal to communicate...
Hello I have used the Windows comms package to talk to a PNC2 and PNC3, but I'm going back 3-4 years so things are a little hazy. I do remember that I had to...
I have a Denford Triac miller and was never able to get Dolphin to communicate with it through Windows. In desperation I tried the DOS version of the Dolphin...
... I guess I'll have to get used to using the "command" field more. I haven't used it much up to now. Thanks for the reminder. ... I think it would be a...
Thanks for the suggestions. now the next snag... I've had partial success, I'm not sure what the exact problem was, usual with comms ;-( I thought it didn't...
Hi, I'm still using version 7 of Dcad and Dcam. What post processor should I be using for a Heidenhain TNC151b ? With my DCAM I have pps " M_h150.ppr" and...
Hello Andrew The 155 post is the one to use, I recently did an installation on a Bridgeport with a 151 control and used the 155b post, it wokred a treat. Could...
... Bridgeport with a 151 control and used the 155b post, it wokred a treat. ... at it. It might be something to do with Vs 7. ... Andre, The way the mill was...
Is there anybody who could spare me some time & help me get started? I wish to upgrade my pclathe software to someting a bit better & it seems Dolphin CAD/CAM...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
