I hurt my foot and it slowed me down so while sitting in the office answering the phone I constructed a small battery really a fuel cell. it runs on oxygen in...
I have been breaking out my welding equipment for a medium large project to construct a wood gasifier powered generator. Some of the welding equipment has been...
Hi Ed. I don't know if you have gotten that DVD available that you mentioned on the YouTube videos, but if so, I'm sure willing to buy 1. I'm trying to figure...
sounds like your going to have lots of construction fun with your cutter , myself i have been playing with an oscillator circuit , its name on the web as a...
I got in a plasma cutter today a 50 amp model GiantTech Plasma Cutter Model Slice50DP and it works very well.I am going to build a wood gas gasifier to run...
I have been up grading my backup power system and just finished a direct drive Dc 94 amp generator to charge up my battery bank to operate my inverter an DC...
I found your videos on you tube and followed you here. I very interested in what your doing. I purchased a roll of carbon fiber and prepared a bath for nickel...
I was putting together a ion vacuum gauge controller circuit and was making a 12 volt power transformer for 30 and 150 volt dc to run the gauge tube.I needed...
I am working on building a oil diffusion vacuum pump made out of stainless steel ,that is hard to cut with out a plasma cutter.So I put together a simple saw...
Beware of using some plastics in your nife battery projects.The last two batteries I built went sour,what I thought was HDPE separator was polyester and nylon...
Someone ask me about building a welder.I just built a spot welder and built a tig welder from scratch some 11 years ago and still use it today. It uses old...
Another battery hack if anybody cares.I bought a task force rechargeable screw driver from the local dumpster diver for 50 cents the 700 milli amp nicd's were...
I manage the apartment complex where my shop is and do night time security checks so I put together a super bright spot light.I picked up a halogen flood light...
I bought a makita rechargeable hammer drill kit that the drill was burned out for $10. It was powered with 3 amp lithiun-ion batterys and had 2 and a computer...
I put together a small spiral wound nife battery today a 2by4and1/4 core on a 10 min charge lock amp test it was 14 amps that's 5 times higher than any I have...
Hi Ed. I was admiring your concentrator/propane setup. Where did you get the concentrator? Surely you did not buy it straight out from a medical supply co,...
I folds I posted a link to edisons patents from 1900-1909 if you look close it has the nife patents with drawings.This is in the link section under edison...
In a attempt to make nickel hydroxide more conductive I mixed it with powered activated carbon 3% water and pressed it in a form at 12 tons of pressure.I...
For the folks who want to try this I did today.I places a pure nickel plate and a iron plate in a 20% sodium hydroxide solution and charged it and tested...
I did a little test today on constructing a fuel cell using nickel screen battery plates I have been making with a thin coating of Raney-nickel electroformed...
I have been working on my electroforming a little bit,I have got the amps.time and temperature for making nickel screen battery plates down.I grew two...
Jack have being in the spot welder trade what kind of tip would you recommend for spot welding nickel sheet metal.It is real [sticky] to the tips.thanks Ed...
I modified my larger spot welder tips.they were copper coated iron and sticking, so being new to spot welding I took thoes tips and drilled them out and...
Well I found out that nickel metal is hard to spot weld so I wound another microwave transformer today.I had a 900 watt on the welder and had a 1200 watt on...
I was asked to do a more detailed battery construction thing so I posted 16 photos of the positive core of my 5by10 in cylinder nife battery.I have made some...
