Hi Mark, How do i create a R1/R2 pairing ..We have created a meta volume of same sizes on Both target and source but cannot find any option to create a SRDF...
Hi Mark, Let's see if I can run down this for you... It takes a couple steps. First you want to create a file that contains the disks you are going to use to...
hi, We have DMX3000 new installed . currently we have in our setup is raid 3+1 "Parity Raid Configuration : RAID-S (3+1)" our team is now configuring the...
Hi, Its been two years since this group was formed. We have come a long way, and our membership has grown dramatically during that period. The list has become...
The 3+1 and 7+1 are the number of usable disk + parity disk. For example the 3+1 layout means that you have the capacity of 3 disks that may be used for data...
Thanks Rita! I use the ECC GUI ...... The on-line help is good. I'd like to suggest that the person posting the question to take a SRDF training class, or get...
Kochanski, Mark A
MKOCHANS@...
Sep 1, 2005 2:16 pm
817
thankd david, but how should i configure .... is that i configure in VXVM. or there any symmetrix facility?? ... Thanks & Regards Sudhir Vernekar Life...
I believe you can configure it in VM. If you have the option to configure it on the Sym, I would go that route Kumar Sudhir <sudhirvernekar@...> wrote: ...
Hi I am new to SRDF and have a simple question, after I have run the SRDF commands and established the link from R1 site do I need to run similar commands from...
Raghav, You dont need to run command from both side but u need to create group on R2 side. raghav sood <sigma77in@...> wrote:Hi I am new to SRDF and have...
Hi Rita, Can you guide me that how to remove unmapped metavolume from SRDF pair, For example I have created a meta volume 23A and add it in SRDF R1 pair. Now I...
Thanks for your reply. I was under the impression that the device group ( not the RA group ) needs to be created only on R1 or R2 site and it would propogate. ...
Hi Freinds, I have created R1 devices as well as R2 devices and masked the devices to particular host,Know when i am Seeing in "symdg list" command on the host...
Hi muzza buddy, You can use following command to change the status of symm. device. #symdev –sid 123 ready – nop Symm.Device For powerpath you have to use ...
Dissolving a Meta Device A dissolve action removes the meta head and all its members. To dissolve a meta device, use the following form: dissolve meta dev...
Hi Vijay, how r u??n howz Canada??Enjoying??? Yaar see i have run all the commands mentioned by you but still the problem persist...when i run symdev list it...
Hi, Please help me if anyone can, My ECC server was getting hanged during creation of logical drive. after restarting the ECC server, I found that logical...
Vijay, I have created a file named \tushar\delete with following contains. dissolve meta dev 023A; and then run symconfigure command, its o/p as below: meta...
Tushar, It seems you have a Symm at home to play with ;-).....Just kidding Try to change your device 23A from RDF meta to meta Standard device (Either thru ECC...
Hi Murtaza, I am fine.. (1)tell me are you running following commands on same host. (2) Have you executed symmask -sid 123 refresh -nop after configuring this...
Hi Tushar, Pl. check whether any lock is there or not? symdev -sid 110 list -lock S Y M M E T R I X D E V I C E L O C K S Device Name Device ... Lock...
To list configuration locks on a Symm: symcfg -sid <serial number of symmetrix> -lockn 15 list To release the lock: symcfg -sid <serial number of symmetrix>...
Tushar, Do NOT dissolve your meta devs unless you want to destroy all the data on that volume... you are looking for the "unmap dev xxx from dir xxx:xxx" ...
You can try the following command symmask discover hba This reloads the local copy of the masking datatbase as well as refresh the Sym copy of the WWN Murtaza...
There are at least 3 kinds of locks on the Symm: A. Symmetrix Locks: 1. I was removing device access with a script and I "Ctrl_C-d" the script, and all further...
Hi, I am trying to designate my devices as R1 and remote device as R2. (Currently standard). Also I need to create a device group and add those devices into...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
