Hi Stuart I have tested using both 4-digit device numbers and 3-digit device numbers and even 2-digit numbers on SE 6.0.1 Its working for both device numbers. ...
Hi folks, Need some advice here. We have a server thar has STDs and BCVs that are mounted on a Netbackup media server for backup. We synchronize this BCV,...
This is called multiple concurrent BCVs, and is possible. Attached is UNIX example. Stuart Filipe Litaiff <filipe.litaiff@...> wrote: Hi folks, Need...
I will be out of the office starting 12/03/2005 and will not return until 12/06/2005. I will respond to your message when I return. ... ...
Roger.Best@...
Dec 5, 2005 5:24 pm
917
Thought I should pass on my knowledge to all you guys (and gals) on here. I know like heaps of men I am pretty shy when it comes to going up to someone. I've...
ignatia.kirkland2847@...
Dec 10, 2005 10:22 am
918
All, Is there a way, to tune cache settings on a DMX Array, and is there a best proactices for the amount of cache that should be on-board. My cache is...
The Symmetrix does not have a tunable cache in the sense of something like the Clariion or other storage array where you designate a certain amount of cache to...
Thanks, this does help ... From: Thomas Crowe <tom.crowe@...> To: emc_list@yahoogroups.com Sent: Wednesday, December 14, 2005 8:31:01 AM Subject: RE:...
Title : Hardware Engineer Location : Stuttgart (500 meters from the Airport) Rate : 55 -58 Euro with poss NEG Start : January Duration : 3 month + Req Type:...
Hi friends Need your expertise in resolving this EMC issue It failed when trying to do a symrdf with a set mode semi command Error msg "Inlines command failed"...
.On Symmetrix you turned them on from the panel in the front. But where do you physically turn on the directors on a DMX2000 ? Or point me to where to read for...
There are no physical switches on the DMX to turn on directors.. it's done via inlines by your CE. Pretty sure you can also do it with SYMCLI (symconfigure)...
hi, i have problem. sys admin ( solaris host) asked for a additional lun and i bind a lun of 2 GB from a raid group and added it to the storage group. sys...
What is the actual disk capacity for a 300GB FC drive for Clariion CX500? I need this information for my storage diagram. The EMC knowledgebase article ...
Rick Asks: What is the actual disk capacity for a 300GB FC drive for Clariion CX500? I need this information for my storage diagram. The EMC knowledgebase...
Rick, Usable capacity for the 300GB FC drives is 268.37GB. If the disks are in slots 0_0_0 to 0_0_4, there is some additional overhead, so you get a little ...
Title : Hardware Engineer Location : Stuttgart (500 meters from the Airport) Rate : 55 -58 Euro with poss NEG Start : January Duration : 3 month + Req Type:...
Richard: There is EMC and there is EMC. The EMC you are looking for is "Electro Magnetic [something that begins with "C"]'. This isn't it. There is also an...
I will be out of the office starting 12/29/2005 and will not return until 01/05/2006. I will respond to your message when I return. ... ...
Roger.Best@...
Jan 3, 2006 3:15 pm
935
Folks Does anyone have steps to migrate from one storage to another on HPUX 11i using VVM 3.5 or higher. we were thinking of using mirroring to migrate storage...
If you are going from one frame to another why not use SRDF? Present new storage on the destination frame making the devices R2 volumes to the source frames R1...
Steve Calderoni
scalderoni@...
Jan 4, 2006 3:57 pm
937
Steve: The "host-based mirroring" technique can be done online during the day with no outage (unless the volumes are HP-UX LVM striped). You don't need an...
I just did this yesterday. You have EMC run a bin to convert FA ports. They didn't charge me to di this the rest is done by me. Very easy to do and there is no...
Steve Calderoni
scalderoni@...
Jan 4, 2006 4:20 pm
939
Don't really have time to write up the procedure docs, but here is a high level overview... Allocate new storage to host Add new storage to existing VxVM...
Folks Thank for your prompt responses. Preference is to through VxVM and not SRDF as we don't have any FA to use for SRDF. That's one of the many reason to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
