I seen on a few websites this is supposed to work on our epods... Anyways, I tried CEShell, BEEPod and epodxp1, and no luck... :\ Any ideas? I tried copying...
I got BEEpod hack installed, and everytime i try to install moneyCE or ministumber or a few other things, when the easy install exe extractor finishes, the...
Just went through this same problem, so I'll help. The fix is actually somewhere in this BB, a search will find it. But to save time... Create the target...
MiniStumbler really doesn't work. It installs and runs, but will not detect an AP's after it's initial detection of an AP. Don't count on a fix for it either...
epods group, I bought an already hacked epods from a guy who has moved away and I can't get in touch with. I let it sit idle for a while and the battery ran...
I am using the Linksys WPC11 and everything in the settings is 100% for connection. But for some reason I am still unable to connect to the web or even to my...
... Have you changed your SSID of your AP from the default SSID? If so, have you entered that SSID into the clientmanager for your network card? Do you have...
Sounds like it was only a soft-hack. Check out: http://www.geocities.com/epodsfiles/ He's got the instructions for everything you need for just starting out. ...
... I think I have entered the SSid in the client manager for the network card. And the correct encryption key in the Epods is in place. Again everything is...
Are you getting an IP address from the network? In other words, is there a DHCP server somewhere on your network giving out addresses? I believe there are ...
Hi, Im new in this group. Is there a better web browser than IE 4 ?. Im using 1XP hack on the Epod. However I cant access to some simple things like Hotmail. I...
Thats been a complaint since first got these things several years ago. The best way is to setup a win2k server and run terminal services on your epods....
Hi, I'm new in forum and epods. I've got EpodsOne from my friend, but it's dead. I can't switch on the unit. Can anyone have schematic diagram, or service...
If it doesn't boot due to a bad hack or lost it's hack due to dead batteries it can be revived a couple different ways. Does the screen actually light up but ...
How do you know the battery is ok? Have you tested it underload? If the Screen doesn't show anything then it's possible it's just the hi voltage board for the...
... I check battery on tester. ... If I press power button, current rise from about 10mA to 190 mA. Screen is black. After reset (on the bottom side) red led...
Then it sounds as though it's booting, but no display. Do you know if this unit was disassembled at some point? it might just need it's ribbon cable reseated ...
... All connectors are OK. Ribbon cable is OK too. There is only two short "knock" in speaker, when i press power button. What can I do now ? Do You have user...
OK, this is probably an oft-repeated question, but I can't find evidence it's been discussed before... Does anyone know where the setting are for the on-screen...
Are you still using the original OS on the ePods? If so, you really need to get it hacked. ... __________________________________ Discover Yahoo! Use Yahoo!...
I disassemble my epods and what I see ... Someone hack them, (pieces of tin on pin 22 and 32 on DOC) display is blank, after reset. (I connct external inverter...
Battery is OK, but ... I got new information from my fried (from wich I've got epod) Epods was hacked, Battery was dead, and he don't change it after six ...
Hi, I change cable (hihg voltage) ,and small success. I used jkgamer metod (pin 22 and 32). I've got callibration screen, but thats all. I'm calibrating, and...
Try doing a hard reset on the device, sometimes that knocks it out of the endless calibration loop. ... __________________________________ Discover Yahoo! Find...
... that ... Hello all, I have a epod with the blue screen and tried going to the karmapc site and it is gone. Does anyone have the instructions that were on...
Can you follow the calibration process all the way through? I mean tap and hold to make the point move through all positions on the screen? When I first got...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
