... they finally got me to send in my keyboard. they replaced some board inside. the sliders now are as they should be. maybe the knobs are too, I have to ...
Hey John... Hope all is well... Right, been hectic with work and gettin these controllers finished - but now all is done ;) and so I'm back on the FM tip... ...
... Um, not sure, but I think what you're asking here is "can I use more than 128 hardware controls"? No, not in this version. I have been thinking along these...
okay, it seems FM won't learn on any other MIDI chan other than 1... yes, i did change the cha box in FM when trying to learn on these chans, have i missed...
... No. As per my previous post, FM supports a single channel of 128 CCs. That's all the banks currently have room for (each learnable parameter is stored in a...
okay John, all good still... only been in a few hrs and already its feeling fantastic! ;) can't tell you enough what its like having control of 128 params at...
i spoke to soon. it seems that when midi remote is enabled the id shift in fm doesn't change value even tho the mixer shifts up and down accordinly, however -...
... Hmmm. What are you using for your FM external shift up/down commands? And what are the assigned midi remote commands for page right & page left (in...
... I'm using ext MIDI control - tried it using both CC and Note msgs, same result with either the 2... ... left (in keycommands)? The same as those assigned...
... OK, that's the problem. The midi remote commands must be different to the FM Ext Shift commands, or the remote will eat the incoming midi before FM sees...
Hey John... Yea, it's been so long since the last time i used FM (or logic), but i do vaguely remember this proceedure for shifting... Thanks again ... From:...
still cant get it :( not ur fault or the text - think i've just lost it is all... right, i've set my 2 ext buttons to: left - note/ch16/e8(124) mode: on/off ...
I remember having to set the page left/right MOST kc's aswell as the regular page left/right ones, doesnt say in the help tho so that cud be added... ta Dan ...
Arggh!! just goin round in circles now... John, can u answer the following: 1. What to set the to the ext control to shift up/down one more time 2. What to set...
sorted ;) i had note OFF instead on (1) for the midi remote page left/right kc's...:/ checking them to on has sorted it all out ;) panic over... ... From:...
... Good. ... That was in the original autoscroll demo, and was so the autoscroll could wrap around when you hit either end. It used way too much internal midi...
Hey JP It's all come together very nicely I must say - and your right, trying to write down the exact way of doing tricks concerning the shift and custom ...
I'm having probs with some additional tracks I've added... I added the new ID macros to em, set the value, and cabled accordingly (to ID in), also added the...
sorted - dble checked the 'to Audio' trans of the added tracks and they were cabled to the wrong audio object - I cudda sworn i cabled them right... ... From:...
I really like how Fadermapper just takes care of me with regard to teh pitchbend wheel. It always bypasses fadermapper. What I *really* want is for the...
Robb Monn
rmonn@...
Apr 15, 2003 7:47 pm
124
... Because it doesn't send CC messages... ... It just needs a single transformer. Step-by step: 1 - Open a new Environment window. 2 - Switch to the "Clicks &...
... Haha - I've taken to waiting a while when your "it's busted" messages come in, just to see if there's a "it's fixed" message a bit later ... Documentation...
... heh, a wise move... ... Yum, sounds interesting. Dunno if i mentioned I was also makin that LC controller as well, but after a few days of setting up the...
... That's 64 0-127 pots, right? Not endless? ... Well, if I had an LC I definitely wouldn't be bothering with Fadermapper... ... The environment I'm building...
Hey John... ... The MB64 is yes, the 8 endless (9 incld scrubb wheel) would be used on the MBLC unit... ... Fadermapper... Noted... ... Gotcha... ... Yeah, i'm...
... Hmmm, well now ... I think I've just figured out how to do that ... So Dan - my VM200 has 12 dials, 9 motorfaders, 19 usable buttons w/lights (ie they...
Hey... ... Your slacking John, that only took like a few hours...;p ... hmmm, not to sure - seems a tad over my head as I've hadn't had to do any of this in...
... Well, at present I've gone the other way - one channel for motorfaders/buttons, another for rotaries, on the basis that most controllers will be more...
... Gotcha, that makes more sense now... ... Nice. This got me thinking - the latest firmware for this MB64 box supports 'virtual motorised faders' as well as...
have you guys seen the 10 control? made by the same guys in germany who made the 4 control for NI. 10 endless rotary knobs and a screen for setting pages...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
