McAfee GroupShield™ Alert McAfee GroupShield discovered a problem with the following email. See your system administrator for further information. Date/Time...
McAfee@...
Oct 1, 2004 7:56 pm
1144
McAfee GroupShield™ Alert McAfee GroupShield discovered a problem with the following email. See your system administrator for further information. Date/Time...
McAfee@...
Oct 1, 2004 8:02 pm
1145
Bob, Although I haven't determine exactly why yet, I found that if you actually remove all of the control points at 42 north latitude, the northern border ...
Mike, Thanks for the idea... I will remove 42° points and see what happens. [In my original note, repeated below, the 9 seconds should have been 49 seconds of...
Hello, I use the pick tool within Global Mapper quite alot. I developed my own propriatary software to create grids to download data for certain areas of the...
I have rectified the 1876 map of Utah and, per Mike's suggestions, removed the 42° rectification points. I agree that gets the 42° border as shown on the...
Bob, I have done some investigation and think that I have found the problem and been able to improve the triangulated rectification so that the points at 42 ...
Bob, I did some test and was able to reproduce your problem. It was actually caused by moving the order of layers around when TerraServer layers were also...
Some of the crashes are gone. However I have still had crashes to the desktop. The following outlines ONE of the crashes. I will report others combos as and...
Files in your TEMP folder don't go anywhere until you delete them using the disk cleanup function under Accessories>System Tools on your Start Menu. Any ...
I cannot get Global Mapper to open this or any of the other dem.zip files, and if I manually unzip I still cannot get Global Mapper to open the included DEM...
Support... What are the limits on what size the GeoTIFF and JPG files can be? I tried to save the area between 37 and 43° and 109.05 and 114.05° with 2 meter...
... That file that you attached makes no sense. I tried opening it as every DEM type that GM uses, with a variety of error messages (usually relating to lack...
BTW, there's very little data in that file. It zipped to 59.3 KB, but expanded to 59.4 M. That's a compression ratio of .00097491845538720538720538720538721:1,...
... I believe that processor and RAM may be an issue in your current case. Don't know. Consider making smaller tiles. Frank ... My mailbox is spam-free with...
Bob, The JPG format is limited to about 65,000 pixels on a side (it's actually 2^16 - 1) as it only uses a 16-bit value internally to store the pixel width and...
Bob, I'll see if I can reproduce your new crash and get back to you. For the TerraServer temp storage, the location used is determined by the setting of the...
McAfee GroupShield™ Alert McAfee GroupShield discovered a problem with the following email. See your system administrator for further information. Date/Time...
McAfee@...
Oct 4, 2004 5:55 am
1162
Bob, This IS a dem file, but as you rightly say, there is no header etc. It will be nearly 100% ocean anyway as it is the South Pacific ocean and about the...
Colin Sare-Soar
colin.sare-soar@...
Oct 4, 2004 6:00 am
1163
Bob, As Mike says elsewhere, BIL files are more-or-less limitless. I have a nice coverage of Europe in BIL format that is almost 2GB unzipped. GM opens it no...
That also explains the compression ratio since most of the values are sea leavel and overall very compressible due to repeated data. From: Colin Sare-Soar...
Tim, I just went to the group settings to check this out and discovered that the group was set up so that anyone could post, not just members. I fixed this so...
Frank / Bob The file unzipped in seconds using XP's built-in unzipper. The data values are all shorts, i.e. 16bit. This is mostly a water tile and the values...
Mike, Apart from the setting you have changed, which was probably for the good, this warning comes waaay too late. This wasn't spam, anyway, but it had been...
Mike, Generating contour lines from a elevation grid with the "Anti-Alias pixel (interpolate)" "on" or "off" I get different results in the generated contour...
Colin, I have the full set of GTOPO30 files, and indeed used that as a substitute, but these are supposedly more accurate. I have BOTH in their entirety on my...
Colin, I will check it out, but for my use I need to take the output into some program that will convert it to a TGA file, which is the format I require for...
To all about the McAfee alert... Lets end the issue, as it is pointless. The program reports falsely and unfortunately too many use it. The message and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
