We are trying to develop an ethernet application with the freescale mcs12ne64 cpu, but we currently run into some problems using the emac module on this chip. ...
7813
Pete
prfetterer
Mar 2, 2006 6:11 pm
I played with the GNU tool chain and the ne64 chips, I havn't gotten around to thinking about the emac as of yet. I always have to modify the memory map of the...
7814
Pete
prfetterer
Mar 2, 2006 6:18 pm
sorry.. I mean Mark B. is the NE64 guru. ... -- Peter Fetterer KB3GTN The force is like duct tape. It has a light side and a darkside and binds the universe...
7815
John-Mark Gurney
gurney_j@...
Mar 2, 2006 6:25 pm
... You access the RAM... the physical address of $0000 is relative to where ram starts... so the physical address you see in the mcu is ram start address +...
7816
Triffid Hunter
triffid_hunter
Mar 2, 2006 10:54 pm
... Last time i saw something like that happen, the board was continually resetting due to chronic power fluctuations...
7817
Eric Engler
englere.geo
Mar 3, 2006 3:56 am
... One of my users ported the uIP stack to the NE64 using gcc. You can get his zip file on my site, but I can't help you with any questions you may have...
7818
jasonwang13
Mar 3, 2006 11:03 am
Note: forwarded message attached....
7819
Mark Butcher
mjbcswitzerland
Mar 3, 2006 4:05 pm
Hi I have a demo project at the following address: http://www.mjbc.ch/software/Demo/j8jdwk-ku7/uTaskerPingDemo.zip It works with VisualStudio and simulates the...
7820
Al Dietrich
adietrich@...
Mar 3, 2006 4:15 pm
Hello, Has anyone had the experience of an output compare interrupt firing immediately when it should be delayed? Chip is MC68HC912B32 Example. TC0 configured...
7821
Pete
prfetterer
Mar 3, 2006 4:56 pm
This uIP port is well done... sweeeet!!!! I got it up in running in under 20 mins :-P ... -- Peter Fetterer KB3GTN The force is like duct tape. It has a light...
7822
Mike McCarty
Mike.McCarty@...
Mar 3, 2006 6:43 pm
... On my Linux machine, I saved that file to disc, and it is a uuencoded Windows executable. I recommend that users of Windows *not* extract, view, or run...
7823
NZG
nzgustavson
Mar 3, 2006 8:27 pm
... lol, no kidding? I have also compiled a list of recommendations: 1. do not open attachements from people you've never heard of , especially if they are...
7824
Eric Engler
englere.geo
Mar 4, 2006 2:45 am
... Mark, you make this look easy, but I can see that you really know your stuff. I've seen your posts here and in the Arm groups. You must dream about IP...
7825
Mike McCarty
Mike.McCarty@...
Mar 4, 2006 5:50 am
... Ok, Mr.Sarcastic, in future, please blacklist e-mail from me. I wouldn't want to waste any of your time reading something which, though it might have the ...
7826
Stcarrez
stephane_carrez
Mar 4, 2006 2:59 pm
Check attached file for details....
7827
Mark Butcher
mjbcswitzerland
Mar 4, 2006 8:17 pm
Hi Eric Thanks. The problem with IP is that it is basically very easy. Then it grows into a Frankenstein's monster - the more you do with it, the more you find...
7828
Eric Engler
englere.geo
Mar 5, 2006 3:36 am
Simulation is incredibly difficult, and requires a lot more time than working with the actual devices. And sometimes simulators look bad because the actual...
7829
JCL
domi2c
Mar 5, 2006 8:38 am
Hello, I've used kermit to exchange with my Dragon12 board under /dev/ttyS0. I load the .s19 file and don't use gdb to debug, but, d-Bug12. All is working...
7830
John-Mark Gurney
gurney_j@...
Mar 5, 2006 9:18 am
... You can use objdump to do this... This will include your source code with the assembly if you include debugging symbols... objdump -S -D -xdC file.elf ...
7831
JCL
domi2c
Mar 5, 2006 3:17 pm
... wrote: Thanks John-Mark, I've tried what you said but after disassembling a lot, I've obtained an objection : machine UNKNOWN. So I seached the objdump man...
7832
Uwe Arends
uwepcb
Mar 5, 2006 3:45 pm
Jean Claude (?), pardon my jumping in, but I think you should use m6811-elf-objdump!?! hth -uwe ... From: "JCL" <domi2c@...> To:...
7833
JCL
domi2c
Mar 5, 2006 7:46 pm
... Hello Uwe, You're right. It works wonderfully. When I said I was drowned in the doc, I think it was real. I hadn't seen that m6811 command. Sometimes we...
7834
JCL
domi2c
Mar 5, 2006 7:47 pm
... Hello Uwe, You're right. It works wonderfully. When I said I was drowned in the doc, I think it was real. I hadn't seen that m6811 command. Sometimes we...
7835
jasonwang13
Mar 6, 2006 9:37 am
Note: forwarded message attached....
7836
ahmed sh3ban
ahmedbndk84
Mar 6, 2006 12:52 pm
I recieved a version 3 of AXIDE program with my package , that don't support EVB9S12NE64 , can any one send me a newer vesion or update plz??? thanks ahmed...
7837
Barry Callahan
melstav
Mar 6, 2006 1:37 pm
Cute. Subject Line is eBook.pdf Virus-laden attachment is eBook.PIF If you didn't cue in on the stereotypical virus email text, you might not have noticed that...
7838
NZG
nzgustavson
Mar 6, 2006 4:00 pm
O I'm sorry, I'm just being a jerk. Seems so obvious these days that I just had to poke fun. Didn't mean to hurt anyones feelings. Note that I did not make any...
7839
Mike McCarty
Mike.McCarty@...
Mar 6, 2006 6:49 pm
... Apology accepted. Mike -- p="p=%c%s%c;main(){printf(p,34,p,34);}";main(){printf(p,34,p,34);} This message made from 100% recycled bits. You have found the...
7840
Jefferson Smith
imajeff84663
Mar 6, 2006 11:19 pm
... Hash: SHA1 And Mike, I don't know if you caught the solution from Stephane. He said his emails will never be posted without encapsulating in a GPG...
