Ok, I'm installing it now. I'll put out an email when I am done as to how it worked. I need backup all my stuff first though... Chris ==== Chris Seto Admin of...
Not in a terribly good mood. The Windows recovery utility is pretty hopeless for getting Debian on the MV2, so I have spent all night trying to get Debian...
I was able to use the HP Windows recovery utility to load Debian, however the install does not complete, I get a message indicating something is missing from...
Hi Gavin, Your post may be stuck in moderation, but you are not set to be moderated so maybe not. Did you send the message from another email address? I'm...
Hello All, I cannot seem to get this to work. I have console access so I am able to watch what is going on. The transfer completes, and the install appears to...
Hi Gavin, First, how are you even getting to this point..? I can't even get past the recovery app. What recovery app are you using? The Wizard like Windows app...
Heya Chris, I am using the HP Firmware update/recovery utility on Lee's page: http://www.leedevlin.com/hpmv1/HPMV2/Setup.exe I am then pointing it to the...
Hi Gavin, Thanks for this, as it helps alot. Give me like 5 minutes to replicate the situation.. Thanks, Chris ==== Chris Seto Admin of hackingthemediavault ...
1. Renamed netboot.img to firmware.bin 2. Started recovery app, did the usual steps, produced a SUCCESS message 3. Watching the health light blink... 4. Still...
UHG! This is just getting frustrating now. uphpmvault wants libc6. That is fine. however I already have libc6! The latest version too. Any ideas? Thanks, Chris...
I take it you don't have console access. That is what happens to mine too, the health light remains blinking purple. It's been like that for hours now... The...
-- Big update -- I have gotten uphpmvault working. I had to compile it from source, then install it. It was basically just cd <the dir the source lives in> ...
Ok, I tried uphpmwault using my knoppix cd. All I had to do was: apt-get update apt-get install uphpmvault uphpmvault netboot.img uphpmwault seems to be...
I tried at least 5 times with no success. Each time I had to yank the plug to turn it off after it failed to do anything. Basically, I would start the app,...
Chris, How far did you get? I was able to SSH in, did the whole thing with partitions, and now it says "Installing the base system" and is about 80% through...
I never got to SSH in. It said it was sending the file, and that was it. Knoppix is downloading now @ 600KB/s, should be done very soon ( less than 5 minutes)...
I think I have Knoppix 5.3.3. The apt-get couldn't find the uphpmvault at first. I did the update and then all was good. Be prepared though, the update is...
UHHHHGGGG!!! I am so sick of this. Now when I open VPC with the Knoppix live CD my mouse doesn't work! I can click all I want in the window, but apparently ...
Well, now I can get into Knoppix and all, but after a fixed period of time, the whole screen minus the bottom bar turns black, and all applications exit. Chris...
Ok, One thing is figured out is that the reason my screen blanks is because I am running out of memory. I pushed it up a few hundred meg and that doesn't...
Me too.. Install is still going. It's configuring the software now (71% through the configuration part). I'll let it keep going. Hopefully there isn't any...
Chris, If you recall I mentioned in one of our conversations the kernel version I saw during boot-up was unusual, like 2.6.12 or something. Well, I found out...
Hey Thanks alot Gavin! I'm in the installer now, and it appears to be working. Do you mind if I use some of this information you have given me in a guide? You...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
