Hi guys, I'm new to the handyboard and electronics in general. While trying to get it to work, one of the contacts from the wires accidentally touched part of...
Hello Aaron, Do you have any idea what wire it was that touched the board and where it may have shorted? It could really have damaged just about anything. If...
Hi Robert, If I'm not wrong, it was the live wire from a 12V power source that touched the side of the board, probably one of the contacts on the IR sensor. ...
The IR input or output? If the input or receiver, this goes to the TIC1 pin of the CPU and you need to replace the CPU. The transmitter is from TOC2, (CPU pin)...
Forum, We are trying to connect a piezo electric film vibration sensor to a handyboard. We cannot seem to figure out how. We have soddered the sensor but we...
Brian Broadwell
bowlingking2081@...
Oct 29, 2008 12:01 pm
5772
First, it would be helpful to know exactly which sensor you are trying to interface. Do you have a brand/part number of your sensor or a link to a datasheet? ...
Mr. Jerry; I faced the problem that you mentioned here. I read what you wrote about "Memory Problem" and its solution. I discharged the NiCd batteries but the...
Hi Alex, I haven't pulled out me schematic and looked it over, but it should me easy a microphone amp close a latching circuit. The solder pads for the start...
Has anyone used HCLoad to download S19 files to the Handyboard. I tried this but I could not get pass the Communication Test. An error message informs me to...
... S19 files you load from HCLOAD are effectively a complete replacement for the Interactive C firmware you probably have installed. You need to hold the...
Hi, it's been a while since I programmed in Interactive C and I'm having some difficulty with (what appears to be) process scheduling. My example below is...
Hi, I have a Sharp IR GP1U58Y that I'd like to use as a reflective object detector. Any advice (or sample code) on how to do this would be very appreciated....
I have 2 servo motors. One is hooked up to Port A Bit 7 (PA7) and the other is hooked up to Port A Bit 5 (PA5). The PA7 servo works perfectly and responds well...
Hi, I updated my handyboard to support 2 Amp motors by changing the 1293D H-Bridge chip by the L298 Chip! using the prototyping area of the expansion board and...
Here are the schematics!!! http://img76.imageshack.us/img76/5182/handy2axc9.png We must remove the l293D chip and wire as shown in the schematics. If you dont...
Hi, I'm trying to do some robotics stuff with a handyboard controller, and am running into a major problem. I'm not a Windows user - I don't have access to...
James Frye
frye@...
Jan 22, 2009 8:29 pm
5793
i had to revive that some time this summer. i had to hack things a bit to make it work, but i am not using it any more, sadly. have you tried compiling it? -c ...
i had to revive that some time this summer. i had to hack things a bit to make it work, but i am not using it any more, sadly. have you tried compiling it? -c ...
I want to connect a computer in linux to collect data from a board or boards I need at the currently 3 temperature sensors and 14 light sensors each light...
I have a quick question: When installing the Dual Servo Routine which directory is it referring to when it asks "servo_a7.icb and servo_a5.icb, the assembled...
RidgeSoft is pleased to announce the availability of the RoboJDE Java-enabled robotics software development environment version 2.0. The major highlights of...
how much are you asking regards .Moshe ... From: okapi222 <okapi222@...> Subject: [handyboard] Handy Board for sale with Serial Interface/Charger $150 ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
