I have 2 servo motors. One is hooked up to Port A Bit 7 (PA7) and the other is hooked up to Port A Bit 5 (PA5). The PA7 servo works perfectly and responds well...
Hi, I updated my handyboard to support 2 Amp motors by changing the 1293D H-Bridge chip by the L298 Chip! using the prototyping area of the expansion board and...
Here are the schematics!!! http://img76.imageshack.us/img76/5182/handy2axc9.png We must remove the l293D chip and wire as shown in the schematics. If you dont...
Hi, I'm trying to do some robotics stuff with a handyboard controller, and am running into a major problem. I'm not a Windows user - I don't have access to...
James Frye
frye@...
Jan 22, 2009 8:29 pm
5793
i had to revive that some time this summer. i had to hack things a bit to make it work, but i am not using it any more, sadly. have you tried compiling it? -c ...
i had to revive that some time this summer. i had to hack things a bit to make it work, but i am not using it any more, sadly. have you tried compiling it? -c ...
I want to connect a computer in linux to collect data from a board or boards I need at the currently 3 temperature sensors and 14 light sensors each light...
I have a quick question: When installing the Dual Servo Routine which directory is it referring to when it asks "servo_a7.icb and servo_a5.icb, the assembled...
RidgeSoft is pleased to announce the availability of the RoboJDE Java-enabled robotics software development environment version 2.0. The major highlights of...
how much are you asking regards .Moshe ... From: okapi222 <okapi222@...> Subject: [handyboard] Handy Board for sale with Serial Interface/Charger $150 ...
Its a $150 or best offer. Daniel Herskowitz 11-15 45th Avenue, #4J Long Island City, NY 11101 e-mail: okapi222@... tel: 718-472-4235 cel: 347-683-4673 ...
Hi, I want to sent commands from the Computer to the Handyboard in realtime. The commands will be simple numbers like 1, 2, 3 etc. From what i understand by...
Hello All! I'm new to the group and I was wondering if I could get some help. I understand that the board is programmed in IC and uses special functions...
... It's just a standard 16x2 character LCD (44780 controller). Nothing out of the ordinary at all. You can buy one much like the original, but with a...
Has anyone attempted to use the TAOS TCS230 color sensor with the handyboard. It has a daughterboard hookup with a 20 pin configuration for input/output...
Hi, I have two handyboards. Both have now gone into a mode where I can't seem to communicate with them at all. When I turn on the board while holding down the...
James Frye
frye@...
Apr 23, 2009 9:33 pm
5851
Hello James, The LCD will usually display a row of all square blocks on the top line when the battery runs down and the bootloader/firmware is no longer in...
... I think that may in fact be the problem with #2 board - after sending the message, I noticed that one of the wires from the battery had broken, so likely...
James Frye
frye@...
Apr 24, 2009 4:09 am
5853
... It appears that was half the problem. I found a Windows system with IC 4 on it, and it downloaded the bootloader & firmware, something I could not get the...
James Frye
frye@...
Apr 25, 2009 4:59 pm
5854
Hi, I need/want to use some assembly language subroutines with the HandyBoard. According to the manual, I need a special version of an as11 assembler, as11_ic,...
James Frye
frye@...
Apr 28, 2009 10:16 pm
5855
Hi, It's been a long long time since I've posted here. I've recently dusted off the robot and am re-doing the drive system to use Kam Leang's bipolar motor...
I have posted an Interactive C implementation of events for the Handy Board here: http://roboticdreams.wordpress.com/. The code enables an event-based...
I tried downloading the latest version of Interactive C 8.0.2 but when it is done compiling the Handyboard lcd says the firmware is IC 4.2. What happened to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
