Hi Alex, I want to try it out. Can you please tell me where I have to change this? I found dasdtab.c. There under CKD control unit definition the bits 2 to 9...
... Your DBGxxx-Message points to it. I watched this problem in the past and I guess IBM fix it in a service pack and bring it back (or similar) when they...
I suspect these are in ckddasd source, as it says in the comment section that 3990-6 is now a default. hth, Alex ... 2 ... might ... try ... need ... 00000000 ...
Alex I modified dasdtab.c with the values you gave. That works fine as z/VM starts now without sense data. However a SHUTDOWN REIPL cause a program check on...
... Can I get a bit of clarification. POO says so, I agree. However running under VM, for as long as I can remember, CP would set the high order byte to FF;...
Hi, I'm trying to set up a Z/OS which must be accessed using TCPIP from another PC within the network. So far, I can't connect at all and I can't find the...
Luc, How is the netstat on the Herclues host? Did you activate IPForwarding on the SuSE? How is the status of the CTC? d u,,,E20,2 BR Fox ... irtt ... 0 ... 0 ...
I am having some dificulty with Tape Drives and AWS files under Hercules. my Tape drive is a Fujitsu M2488E (3490E Compatable) I have my AWS files defined to...
Hi, IP forwarding is OK. Execution of "cat /proc/sys/net/ipv4/ip_forward" returns 1. The display unit MVS command returns the following: IEE457I 01.07.05 UNIT...
Luc, I think that look all fine. That one of the addresses is A-BSY and the other not I think it is ok. However you have to reach the other side of the P2P...
Suspect the PC needs a route through the network to 10.0.16.2 via the IP address of 10.0.2.14. If this is a corporate network and the PC is not on the same...
Hi All! I work with Hercules lots of years â€" my first experience was in 1999. A couple of weeks I installed last version of 32-bits software set for Win32...
On Fri, 29 Jun 2007 16:41:28 -0300 ... Yes z/VSE 3.1.1 is running properly under Hercules 3.05. But z/VSE 4.1 is not. The z/VSE 4.1 is failed at IPL time. ...
Yep – I have been totally unable to get Hercules networking or tape processing to work correctly under Windows. It may be some of the new processing that is...
Hi, When I follow the guidellines as described on page hertcp.html, that should be sufficient to access mainframe TCPIP stack from any other machine... Or is...
In version 3.05 the default control unit type for 3390 was changed from 3990 to 3990-6. This does seem to have caused some problems for some people, including...
You need to make sure that you have done what is appropriate under "Defining a route to Hercules TCP/IP" on other systems who need to communicate with the...
The other thing that 3.05 introduced is Diag 308, but from what I tell not the parts that Linux expects to be there. When I boot my Linux 2.6.21 kernel, it...
Hi, Pinging from my Hercules host system to my Hercules guest OS doesn't work, neither can I ping in the other direction. I can only ping from (any) another PC...
The Linux DASD drivers do things a lot like z/VM does things, for obvious reasons. Obviously, I cannot load a copy of z/VM on Herc to see what would happen,...
Well I finally got it to work. On the Misc2 tab under Perferences I specified: EXTERNALGUI for Extra Arguments(s). The comments for that say that EXTERNALGUI...
Hey Roger - I must be dumb, but I normally use this line to define DASD: 0A00 3390 /usr1/herc/dasd/USER001.3390-3.0A00 Putting a cu=3390 anywhere on that line...
Duh. I am also afflicted with "refrigerator blindness". Thanks -Paul From: hercules-390@yahoogroups.com [mailto:hercules-390@yahoogroups.com] On Behalf Of...
Hi Paul, I dont think that this is a 64 bit problem. I have the same problem with the 32 bit version under windows. With Fish offline I have had no luck trying...
... and ... sound like contradictions to me. Please provide: Hercules guest IP address (MVS TCPIP stack address) Hercules host tun tap address Hercules host...
... I run Linux native on Hercules. With 3.05 it breaks on the diag 308. This has nothing to do with disk I/O but deals with the IPL parameters. Rob...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
