Is Hercules set up in any way to make the maximum size of one of these virtual tape files correspond with the capacity of a ten-and-one-half inch, 2400-foot...
68497
Enrico Sorichetti
e.sorichetti
Jun 28, 2012 2:54 pm
... look at the MAXSIZE and EOTMARGIN parameters for the tape device definition cheers Enrico...
68498
Enrico Sorichetti
e.sorichetti
Jun 28, 2012 3:05 pm
... look at the MAXSIZE and EOTMARGIN parameters for the tape device definition cheers Enrico...
68499
Robert Duncan
dosvsoperator
Jun 28, 2012 3:16 pm
When I pull up the 'Reinitialize TAPE Drive' dialog box in HercGUI I have a default Tape Size of 170 MB and an EOT Margin of 128 KB. I think I understand the...
68500
Mike Schwab
maschwab
Jun 28, 2012 3:23 pm
That is how much capacity is left when you get you volume full indication. Allows for the remainder of the last write to complete. Should be bigger than the...
68501
Robert Duncan
dosvsoperator
Jun 28, 2012 3:30 pm
Thanks, Mike! 170 MB would correspond roughly to the capacity of a 2400-foot, ten-and-one-half inch reel of one-half inch tape, IIRC... Yours truly, Robert S....
68502
Dave
g4ugm
Jun 28, 2012 4:11 pm
... Its configurable. See http://www.hercules-390.org/hercconf.html#3420 and scroll down to the MAXSIZE options Dave Wade G4UGM Illegitimi Non Carborundum...
68503
Tony Harminc
tzha1
Jun 28, 2012 6:47 pm
... This is conceptually the amount of tape remaining on the reel after the trailing reflective marker. The marker is not right at the end, both so the tape...
68504
Robert Duncan
dosvsoperator
Jun 28, 2012 9:20 pm
Hi, Tony! That's what I initially thought it might be because I remember those slivers of reflective tape from back in the 1970s and 1980s. I didn't realize...
68505
jcfadel
Jun 28, 2012 10:15 pm
I am facing some problems to bring up my system console on a Mac OSX 7.4. I configured the CTCI connection as following: 0E20.2 3088 CTCI -d -n /dev/tun0...
68506
John P. Hartmann
ibm007282
Jun 29, 2012 9:40 am
Did you enable IP forwarding? ... [Non-text portions of this message have been removed]...
68507
John P. Hartmann
ibm007282
Jun 29, 2012 9:41 am
Proxy ARP?...
68508
Dan HorĂ¡k
horakd7
Jun 29, 2012 11:05 am
There was a little inconsistency between the Fedora and Everything repositories requiring a last minute respin, but the Fedora 17 GA release for the IBM System...
I'm using Linux and have my VM system in a separate network, but it looks like I have no porxy arp active. [servus:/home/hercules/sandhawk/sal] traceroute...
68512
Richard Higson
phark0ff
Jun 29, 2012 1:52 pm
... you might want to `man arp` On a Mac I have here I get the following: -s hostname ether_addr Create an ARP entry for the host called hostname with the...
68513
Peter Glanzmann
peter_glanzmann
Jul 1, 2012 1:30 pm
Hi Robert You're right - it should be mentioned, that XMIT manager will not install on 64-bit Windows systems. I will add some comments about it. See...
68514
Peter Glanzmann
peter_glanzmann
Jul 1, 2012 1:30 pm
Hi John First I thought about adding "unXmit" additionally to the Installation Guide. Meanwhile I tend more towards removing all products that are not directly...
68515
John P. Hartmann
ibm007282
Jul 1, 2012 1:56 pm
Peter, rather than purging the manuals of non-Hercules information, may I suggest you move it to an appendix? ... [Non-text portions of this message have been...
68516
Peter Glanzmann
peter_glanzmann
Jul 1, 2012 2:11 pm
Hi John I will think about it. Maybe an appendix is for sure the better place for non-Hercules information. My point however was more that it's not feasible to...
68517
Roger Bowler
rogerbowler
Jul 2, 2012 1:15 pm
In a 2007 Google lecture, Linus Torvalds explains Git: https://video.linux.com/videos/techtalk-linux-torvalds-on-git...
68518
Urtzi Larrieta Alvarez
ularrieta
Jul 2, 2012 1:45 pm
Hi: Is there any possibility to configure Printer Sessions emulation under Hercules? If I define 4 3270 displays in Hercules configuration file (0700.4...
68519
Kevin Leonard
kl_j76
Jul 3, 2012 1:48 am
... You need to configure Hercules to see the device as a printer rather than a display. Assuming the device number is 0C7, define it as: 00c7 3287 in the...
68520
maintain_bj
Jul 3, 2012 8:59 am
Hello, I use the Hercules to convert the ZPDT CKD file the following information: DASDCOPY error message HHCDU013E CKD initialization failed for d:\DEMO\xxxxxx...
68521
Mike Stramba
mstramba2000
Jul 3, 2012 10:30 pm
I googled for "why space instead of *" .. etc, no hits. Why do so many HLASM programmers seem to prefer SPACE 1 /2, instead of (IMO) the more 'innocuous' *...
68522
Tony Harminc
tzha1
Jul 3, 2012 10:56 pm
... I'm not sure about 'innocuous'. I think it's a question of appearance when printed. Those blank lines just look nicer, imho. And with the modern...
68523
paoloG
giacobbis
Jul 5, 2012 6:50 pm
Hi, Unfortunately I never saw a ZPDT CKD disk image (I wish I could...), but I found some useful informations: 1)"The AWSCKD format is the same as that used by...
68524
Tony Harminc
tzha1
Jul 5, 2012 7:51 pm
... Interestingly similar - at a high level, at least - to the Hercules notion of shadow files. And even more interesting because there is still a pending US...
68525
BruceTSmith
Jul 6, 2012 12:23 am
Don't you just love closed source? :) :) :) B.....
68526
John P. Hartmann
ibm007282
Jul 6, 2012 8:58 am
Send me the first 512 bytes of the file: dd if=<fn> bs=512 count=1 of=4john [Non-text portions of this message have been removed]...
