That whole business of swapping bits and bytes confuses the issue. Just take the raw 1st and 3rd bytes reported by the W800RF32A and compare them with the two...
I thought I posted this but, looks like it didn't "take" the first time around :) I recently upgraded my system OS (Xandros). Before doing the upgrade, I...
Hello all, I recently upgraded my system (Xandros). Before doing so, I backed up my .heyu directory so I wouldn't have to reconstruct everything. After the...
On Fri, 07 Jul 2006 02:01:28 +0000 ... Send me a copy of your complete x10config and x10.sched files by private email and I'll see what I can figure out. Also,...
Download this new release from http://www.heyu.org There are several directory changes in this release. Please read the "What's Changed" section carefully. ...
A minor bug came to light shortly after heyu-2.0beta.6 was uploaded to the www.heyu.org website and after the announcement message was sent to the heyu_users...
I bit the bullet, and finally compiled the 2.0beta6, and upgraded from 2.0 ALPHA5. Now I get the following error... Config Line 75: Invalid character '-' in...
I figured it out. I looked at lines 75-77 of my x10.conf file and found that I had hyphens in the Thermostat Setback Aliases I have assigned. I replaced the...
Heyu version 2.0beta.6.2 is now available for downloading from our website http://www.heyu.org/download Release notes for Heyu 2.0beta.6.2 07/22/2006 File...
I just noticed that X-10 has replaced their old document "XTC798.DOC" describing X10 Extended Codes with a new one, "xtdcodes.pdf", on their web page...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the heyu_users group. File :...
heyu_users@yahoogroup...
Jul 27, 2006 3:17 am
1269
Greetings: I uploaded diffs for ATT/NCR svr4 into the files section here; heyu2.0 b6.2 is working well, using a CM10A module on a terminal server slave serial...
Greetings: I would appreciate comments regarding your experience of transmission delays (perhaps in the presence of line noise or interference). We are...
(I tried posting this about twenty minutes ago but it didn't appear; if Yahoo should happen to save it from oblivion and it is double posted please forgive me)...
Michael, There are major issues with your diff file. I'll contact you by private email to resolve them. Regards, Charles Sullivan On Thu, 27 Jul 2006 03:28:47...
Greetings: The previous versions of the AT&T svr4 patch was a quick and dirty hack; it has been replaced by a patch which should not break builds on any other...
Greetings: cm10a.c has a number of references to eia flow control and cable connections; I'd appreciate some clarification: e.g. 1. toggling of RTS can cause...
On Fri, 28 Jul 2006 15:15:06 +0000 ... The CM10 generously donated to the Heyu project by Steve Sykes is the only one I've tested (or ever seen). It's labeled...
... Our CM10A is IBM 75H8381 "2-Way Serial Interface" and it uses an RJ10 4-pin modular connector (tel. handset connector) ... It is evidently a different...
On Sat, 29 Jul 2006 04:33:24 +0000 ... I'm guessing that yours is a later version, just because the 4-pin connector is used on the CM11A. Is there any...
... No sticker of any kind on it; FCC ID: 84SCM10A; IBM R.T.P. NC27708 ... There was a typo that reversed a comment delimiter in my patch for cmd.c; now fixed...
NOTE: ***great frustration with Yahoo Groups*** posts are often delayed hours at a time and now, while composing, I just hit the tab key and suddenly "Message...
... I should also clarify that the CM10A is now on a circuit with little interference since I discovered that line noise (from power supplies and whatnot) can...
... I didn't relish that chore so instead I used a terminal emulator (as described elsewhere) and found that I could issue the address, OK,command,OK sequence...
On Sat, 29 Jul 2006 18:16:51 +0000 ... The FCC ID prefix is probably B4S, which signifies X-10 from their previous incarnation as BSR (USA) Ltd. Interesting!...
On Sat, 29 Jul 2006 19:54:59 +0000 ... If you're seeing multi-second delays, you ought to be able to print the raw system time between each packet sent to and...
... This is a long post; I hope the web interface preserves the formatting. I've build 'heyu' with profiling enabled and statically linked; here is a report...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
