Hello Charles, I certainly do not want to harass you (that's absolutely not my intention...) but I would like to know if it is possible for you to announce a...
Heyu version 2.2.0 is now available for download from the Heyu website http://www.heyu.org/download Release notes for Heyu 2.2.0 02 April 2008 What's New ... ...
Hello Charles, I've just seen your announcement for the new release 2.20 I'am feeling dizzy... You really did a huge work to include so many new features. Many...
I don't think anybody would normally compile the source ON the NSLU2; that's usually done by cross-compiling. I'd think you could use any binary compiled for...
I purchased a Firecracker system from X10 several years ago, the system works fine under XP (with the CM17A), but I can't get it working with Fedora and heyu....
On Sat, 12 Apr 2008 17:08:21 -0000 ... Glenn, There's no way for Heyu or any other software to know if a CM17A is connected to the serial port since it's...
... the ... got ... to /dev/ttyS1. ... and ... normally ... LCK..heyu* ... I cheked BIOS - both serial ports are enabled. Rebooted the system after adduser to...
my x10 system with cm11a works fine with my serial port, I want to use the serial port for my UPS interface, ive setup heyu for USB, I can send and control x10...
... It would probably useful to at least mention what system you're using, since heyu runs on hardware from stock PCs to embedded CPU's on NAS hard drives,...
linux ubuntu, how could i have configured it wrong ? what else should i check / configure ? ... to use ... can ... commands ? ... from any ... using, ... NAS...
On Sun, 13 Apr 2008 08:04:52 -0000 ... Have you just added the UPS? Many of these add enough noise on the line to swamp out X10 signals. Since you mention RF...
USB - serial adapter must be working ... I can send x10 commands fine ... ? yes I am using a trasnceiver, I dont think its a noise issue because everything...
... This isn't a particularly good assumption; many USB<->serial adapters are broken, have flaky firmware, or don't work well with all drivers. Perhaps it...
Despite your thoughts on the noise issue, I would urge you to try the experiments I suggested. Now when you change ports as you have done, it's not sufficient...
Ok, this is what I've got set up: A linux box running heyu CK11A serial interface RR501 transceiver MS13A-C Motion detector heyu log is active This equipment...
On Fri, 18 Apr 2008 23:29:10 -0000 ... You can test the RR501's ability to send and receive signals over the power line, but not its ability to receive RF...
Heyu version 2.2.1 is now available for download from the Heyu website http://www.heyu.org/download Release notes for Heyu 2.2.1 19 April 2008 What's New ... ...
A couple years ago, I wrote some free X10 software for the GPL software behind Logitech/Slim Devices' Squeezebox audio players. My software uses the 'br'...
A couple of years ago I tried Heyu on Cygwin. Several source code mods were required for it to compile - their effect on operation are unknown to me. My...
... been ... stop ... Now, ... know ... if ... circuit ... the ... what ... not ... by ... address. ... Thanks Charles for the answer. The RR501 is on C1. So...
On Mon, 21 Apr 2008 00:46:48 -0000 ... Geoff, That's correct insofar as powerline communications are concerned. But it doesn't verify that the RR501 can...
... up. ... new ... as ... little ... batteries ... programming ... see if that ... Charles - This is a remote location (actually Mexico) where I have no...
Hello could i suggest a new feature ? If we reboot computer, there is no entry about engine/daemon restarting into the monitor log ... Is there a way to do...
Hello, when I ask for a dimlevel of some shutter modules, its shows the number 840. I paste the heyu commands out: p3ntium@pan3l:/usr/share/h3yu$ heyu on c4 ...
Hello, when I ask for a dimlevel of some shutter modules, its shows the number 840. I paste the heyu commands out: p3ntium@pan3l:/usr/share/h3yu$ heyu on c4 ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
