Hello, I solved a similar problem by placing an 'old' (very old) PC with serial ports next to where I wanted my CM11a, in my case the boiler room (local ...
Hello, I have a couple of the KeypadLinc controllers from Smarthome which I would like to program beyond just the lamp on/off mode. They recommend the use of a...
On Sun, 02 Nov 2008 14:45:05 -0000 ... Tony, If you read section "DIRECT COMMANDS" in man page heyu(1) or run 'heyu help' you'll find the commands 'heyu...
Hello, Thanks to everybody for your responses. Of course increasing the X10 signal will be the best solution and I thought about this one but my strategy was...
Heyu version 2.4.0 is now available for download from our website http://www.heyu.org/download Special note: Compilation under Ubuntu 8.10 Intrepid and...
I have worked out that the results form the test are due to the fact that I had to remove the xxd code as I don't have it! This return is equivilant to a5 in...
Mark, I'm not sure what the messages mean. Were those "Yen" characters appearing every 1 or 2 seconds? Let's check that your copy of "xxd" is working as...
I don't have xxd installed (and can't get it) but the yen character is the ascii for 0xa5. When I run heyu monitor it says: DiskStation> heyu monitor CM11A...
Hi, I have a X10 installation with a CM11 module, TM13 and AM12 modules. When I am sending an on/off command on these modules, I can hear them turning on and...
Mark, Heyu is reading the 0xa5 signal from the CM11A but is apparently unable to write to it. Two possibilities are: 1. The CM11A has failed or its cable has...
On Wed, 12 Nov 2008 18:04:29 +0100 ... I suspect you may have a weak X10 signal reaching the modules, and the fan or alarm are putting enough noise on the...
Hi Charles, thank you for your answer. As you know I am developing an X10 library for the Hop a language to develop ubiquitous web applications (like ...
Hi again, doing some other tests I found out that using the serial adapter instead of the usb/serial, I am getting this (see below). It seems to mean that the...
Anne-Marie, 1. You'll need to find out what's inside the plug strip. Is it just a multiple socket or does it include some surge-suppressor filtering? If the...
Hi, I'm trying to get the smoke detector to work with heyu, a marmitek sd90 I get om logs from the smoke detector 11/13 00:39:45 Inactive sensor K15 (Rook) ...
On Thu, 13 Nov 2008 21:10:09 -0000 ... The information I originally received about the SD90 indicated two different signals: Test (from pushing the button) and...
Charles, I have an SD90 happily reporting a "clear" signal every few hours. $ grep SD90 ~/.heyu/x10config ALIAS smokesensor M8 SD90 0x54D2 $ heyu show...
Dave, You're right. I've discovered that the SD90 is a more complex device than originally thought. Stay tuned. Regards, Charles Sullivan On Sat, 15 Nov 2008...
kroon040: I've sent you a private email at your yahoo.com email address. Please respond via private email. Regards, Charles Sullivan On Thu, 13 Nov 2008...
Charles, De raw data, the first is the test, second real smoke 11/15 18:39:32 rcva func RFrawdata : Data (hex) 29 c0 cf 26 d9 54 80 11/15 18:39:32 rcva...
At least I thought I did. I got the following message back: Your message was rejected by f.mx.mail.yahoo.com for the following reason: delivery error: dd...
kroon040 (Richard): I just re-sent the private email but it was again rejected by Yahoo. Please send me another email address to use. Regards, Charles Sullivan...
Thanks again Charles. We finally used the serial port directly instead of serial2usb and it seems to solve much of the problems. We still receive some garbage...
Hello Charles I'm still playing with my digimax sensor add they work fine with heyu. I was trying to manage them as my oregon sensor and tried to get value of...
... heyu. ... Hu" ... oregon' ... to ... after ... such ... such ... Oupssss, I'm so sorry, and that's great that exist, in fact I checked only the heyu man...
I am using scene controllers to send commands to heyu, which then works out what lights to switch on or off. I use the normal switch on/off to control the main...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
