Hi, Some comments and maybe an answer to the following problem. ... I took a look in the code of heyu version 2.4.0 and I found that the effective user is not...
I am running RH Linux 8. I checked my permissions for the port with the CM11 and they are set to crwxrwxrwx with owner set to root and group set to uucp....
Instead of reinventing the wheel, maybe someone has already done this. I have just received 2 AM14A 2-way appliance modules and need to know how to set them up...
On Sat, 06 Dec 2008 09:48:26 -0000 ... Ed, You don't have to do anything. When first powered up (after being unpowered for more than about 30 seconds or so),...
Thanks for getting back to me. First some background info: Heyu is version 2.0beta.10, the server's os is RedHat 8 (2.4.18-14). The AM14A's are marked 'X10...
Ed, I looked at the log file you attached to your private email. (As you've learned, Yahoo strips attachments from messages posted to this forum.) There have...
Thanks for your help. I did the upgrade of Heyu to 2.4.0 and it seems to have solved a lot of problems. I was running the older version of heyu because I had...
Ed, When you experience an address that doesn't agree with the codewheels, spin the codewheel around a time or two to rub off any dirt or oxidation that may be...
Hello list, I have a strange problem; I can not set the house code and unit code on 3 of my LM15 modules. I followed the Marmitek manual but no luck. (tried it...
On Sat, 06 Dec 2008 23:43:46 -0000 ... Frank, Possible poor contact (or defective LM15): Does the lamp reliably turn on and off if you send the X10 signals to...
Hello, I have been using x10 for a few years in a very simple setup to control a few lights. I recently became interested in monitoring and controlling x10...
Michael, Try running the following shell script to verify that your system can at least receive data from the CM11A (assuming the CM11A is sending any). From...
... Thanks for the reply. I had already found that script in the mailing list and tried it. I of course forgot to mention that in the previous email. :( ...
Michael, On ActiveHome, seeing just "Reading" instead of a ticking clock like the system time is a sure indication of no communication. The most likely problem...
... Thanks, I tried the test and I get 'This is a test' in the first xterm window. I will assume the USB-serial adapter is not the issue. Sadly, Shipping it...
Hi All, I'm just starting out with X10 - I've got a few switches/dimmers wired, a 'manual' X10 controller - and now, a CM12U (which as I understand is a 230v ...
Karl, One further question: When the problem occurs, does it afterwards persist if you send an X10 signal on the power line with your 'manual' X10 controller? ...
On Sat, 13 Dec 2008 16:15:15 -0700 ... Michael, Among the current CM11A "RCA HC60RX" sellers on eBay, I think you'll do OK with either "sheridan-b5" or "The...
--On 13 December 2008 23:15 -0500 Charles Sullivan ... Hi, Yes, it's an 'authentic' serial port - not a USB connection at the PC end :) ... Nope, as I said in...
--On 13 December 2008 23:38 -0500 Charles Sullivan ... I've read about that problem on another forum - like the other suggestions, I'll give it a go next time...
--On 13 December 2008 23:15 -0500 Charles Sullivan ... No, it exits cleanly. It happened again tonight, so I did: heyu stop (Which cleanly shutdown the...
--On 13 December 2008 23:38 -0500 Charles Sullivan ... Hi, Manually sending an X10 signal doesn't seem to do anything for it - nothings logged by heyu, and the...
... You're not using the correct device for your serial port. It should look more like this: /dev/cuad0 The tty serial devices are used for DIALING IN, and...
--On 14 December 2008 22:19 -0600 Michael Stowe ... I've switched to using /dev/cuau3 - and that seems to work so far... TBH - for all the other serial...
--On 14 December 2008 22:19 -0600 Michael Stowe ... Rather typically - it lasted all night (and most the morning) using caud3 - and I just tried a simple 'heyu...
... That device implies a USB<->Serial device, not a raw serial port... This could potentially be the source of your problem. Do you have a real RS232 port...
--On 16 December 2008 09:45 -0600 Michael Stowe ... Hi, It is a 'real' serial port, i.e. 9 pin RS232 onto PCI card, the kernel (remembering this is FreeBSD)...
... Whoops, I neglected to consider multiport cards. It certainly seems you've set the right kernel hints to get the multiport card working properly. Is it...
--On 16 December 2008 10:04 -0600 Michael Stowe ... Don't think so - it does *work* - 'most' of the time... I just tried another 'heyu -v date' now, and it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
