Hey all, I've been looking through documentation and can't seem to figure out if this is possible. I want to kick off a script if a flag is set and heyu...
On Fri, 1 May 2009 07:45:33 -0400 ... Tom, I assume you already have something like this: SCRIPT -l MusicOn M8 on <source> :: @setflag 8; my_player on SCRIPT...
... Ah, thank you. This will also solve my issue of wanting to change the behaviour of the arm button - but I do feel there should be an easier way to...
On Sat, 2 May 2009 18:35:40 +0100 ... Roy, One solution is to substitute the functions "Alert" and "Clear" for "Arm" and "Disarm". Or alternatively define two...
... Yes, either of those options would seem like a reasonable way of providing the functionality. ... The way I have it set up now when you press the arm...
Also, I now notice that the use of the 'E' suffix (for Europe, presumably) is very inconsistent on these modules. So the keyfob says KR18E on the box, but on...
A number of Heyu users have offered to contribute towards the purchase of an Oregon Scientific WMR80A Weather Station so that support for Oregon remote Wind...
Spring has sprung here in Seattle again, and again my basement is flooding. Is there a configuration of hardware and Heyu that would help me create an alarm...
On Thu, 07 May 2009 01:49:59 -0000 ... Rob, Here's one possibility: http://www.smarthome.com/71932/X10-Water-Moisture-Sensor-CR1/p.aspx Hook this to an X10...
The X10 Powerflash Interface has a two methods you can use to detect wet or dry Using a 12/24 transformer to have the unit run in "normally open" when water...
Hello; I am running FC10, kernel 2.6.27.21-170.2.56 and I have an Activehome CM11A, that responds version 7 to heyu info. I am running the latest version of...
... Don't know where to get them now nor if they make them for the US X10 Security RF frequency but I've used a few of these: http://letsautomate.com/11146.cfm...
On Thu, 07 May 2009 17:50:23 -0000 ... Bob, Is this a problem which has only recently surfaced on a system where Heyu has been running satisfactorally some...
Wix, The basic problem I can see is than a lot of people would be unhappy about having wires perpetually running under the refrigerator door seal, and routing...
Hi, I've installed Heyu on an embedded PC (Geode CPU 400Mhz / 512Ram) under Unbuntu 9.04. I got a 1xCM11, 1xLM12 1xAM12, 1xTM13F, 1xX10 remote. I've also setup...
Check out the "Sources" section of the x10scripts manual. Short excerpt below: SOURCES By default, a script is launched only when the X10 function is received...
... Hi Bob, I know of two possible reasons I have happened to experience: 1. Driving USB version of CM11 over its original USB cable. Replacing the cable with...
Hi Charles; I have been using Heyu, with this cm11a, since early in Heyu 1 days. I started out with Redhat 2 and have upgraded when ever there was a chance....
Bob, If the CM1A is connected to a real serial port (as opposed to a USB-Serial adapter), I'd suspect a hardware problem with either the CM11A or the serial...
Good news! Contributions have fully funded the purchase of a Oregon Scientific Weather Station and a model WMR80A was purchased per plan. (A local Radio Shack...
Instead of the one-on-one exchange envisioned in my earlier message, I've set up the heyu_beta discussion group on Yahoo Groups, with membership restricted to...
Hey guys. I have been a long time Heyu user (2.0). Heyu runs so well at my house, I don't have a need to mess with it - ever. As a result it has been a...
Rather than try to do it all in the config file, why not just have heyu invoke a bash script so you can manipulate the subject line before invoking mutt?...
Like I said it's been a while since I have done anything with Heyu or Linux. I think I got it here... SCRIPT f5 on rcvi rcvt :: (date) | mutt -s "The mail is...
And I'm also a newbie and don't know anything about mutt. I take it that "(date)" ends up as the body of a message with a subject line of "he mail is here!",...
thats correct. In twitter it is displayed as "The mail is here!" followed by the date and time. I have some motion sensors that i am going to have "tweet"...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
